Finding your suitable load cell 10 kg is not easy. You may need consider between hundred or thousand products from many store. In this article, we make a short list of the best load cell 10 kg including detail information and customer reviews. Let’s find out which is your favorite one.
Reviews
1. Uxcell a14071900ux0057 10Kg Aluminium Alloy Electronic Scale Load Cell Weighting Sensor Replacement
Feature
Product name: load Cell; model: yzc-133; rated load: 10kg /22lb; rated output: 1+/-0. 15mV/VInput resistance: 1066 +/- 20 Ohm; output resistance: 1000 +/- 20 Ohm; insulation resistance: 2000 Ohm; working temperature: -20C to +65C
Compensated temperature range: -10C to +50C; Safety overload: 120 percent F. S; recommend excitation Voltage: DC 5V; max excitation Voltage: DC 10V
Total Size: 81 x 12. 5 x 12. 5mm /3. 1" x 0. 5" x 0. 5"(L*w*t); thread diameter: 3. 4mm / 0. 12"; Hole center distance: 40mm/1. 6", 70mm/2. 8"; cable Length: 240mm/ 9. 4''
Material: aluminum alloy; color: Silver Tone; weight: 32G; package content: 1 x load Cell
Description
Used widely in home kitchen scales, platform balance, belt scales and other electronic weighing devices.2. NOYITO 1kg 5kg 10kg 20kg Load Cell and HX711 Combo Pack Kit - Load Cell Amplifier ADC Weight Sensor for Arduino Scale (10kg+HX711)
Feature
Load cellSturdy aluminum alloy construction with strain gauges pre-attached with strain relieved wires. Accurate measures forces from 0-5kg/ 5kg /10kg /20kg.HX711 :This top of the line load cell amplifier mounted on a breakout board pairs perfectly with the load cell to provide fast, accurate force measurements. It measures small changes in the resistance of the strain gauges mounted to the load cell and passes these values directly to any micro controller (like an Arduino or Raspberry Pi).
Load cell specs: 22 cm (8.5 in) wire leads pre-attached. Dimensions 12.7 mm high, 12.7 mm wide, 80 mm long (0.5 in x 0.5 in x 3.15 in). 4 mounting holes, 15 mm spacing on each side. One both holes tapped M4 thread, the other side both holes tapped M5 thread.
HX711 specs: Operation Voltage: 2.7V-5V ; Operation Current: < 1.5mA ; Selectable 10SPS or 80SPS output data rate ; Includes breakaway headers for connection, soldering required.
Please choose the correct specification before buying. (A total of four specifications).Please refer to the picture on the left of this page for the product wiring diagram.
Description
DescriptionLoad cell - Sturdy aluminum alloy construction with strain gauges pre-attached with strain relieved wires. Accurately measures forces from 0-5kg/ 5kg /10kg /20kg.
HX711 - This top of the line load cell amplifier mounted on a breakout board pairs perfectly with the load cell to provide fast, accurate force measurements. It measures small changes in the resistance of the strain gauges mounted to the load cell and passes these values directly to any microcontroller (like an Arduino or Raspberry Pi).
HX711 specs:
Operation Voltage: 2.7V-5V
Operation Current: < 1.5mA
Selectable 10SPS or 80SPS output data rate
Mounted on breakout board
-ncludes breakaway headers for connection, soldering required
Connections:
Red wire to E+
Black wire to E-
Green wire to A+
White wire to A-
Package Included:
1xLoad Cell and HX711 Combo Pack Kit
3. SainSmart Parallel Beam Weighing Load Cell CZL601 6KG 10KG 40KG (CZL642 300KG)
Feature
Suit for electronic top scale, floor scale and other weighing equipment.Made of alloy aluminum
Hermetically sealed with glue to IP65
Integral structure and easy installation
Description
Features:Ingress protectionIP65 Not to be affected by water-sprinkle from any direction in a short period of time.
Surface anodized and anti-corrosion
Rated load 3~40 KG
Integral structure and easy to install or calibrate.
The product is suit for electronic top scale, floor scale and other weighing equipment.
Specification:
Precision : C2
Temp. effect on span(%F.S/10): 0.02
Comprehensive error(%F.S) : 0.02
Temp. effect on zero(%F.S/10) : 0.03
Rated output(mv/v) : 2.00.1
Compensated temp. range( ) : -10+40
Creep(%F.S/30min) : 0.02
Use temp. range( ) : -20+60
Zero balance(%F.S) : 1.0
Excitation voltage(V) : 912(DC)
Input resistance() : 40510
Safe overload (%F.S) : 120
Output resistance() : 3503
Ultimate overload (%F.S) : 150
Insulation resistance(M) : 5000(100VDC)
Defend grade : IP65
Pack List:
1 x Parallel Beam Load Cell
4. Tedea-Huntleigh 1042 Single-Point Load Cell, 10Kg, 20A
5. Pull Pressure Force S-type Load Cell Sensor with Cable 5KG 10KG 30KG 100KG 200KG 300KG 500KG 1T 1.5T 2T 3T 5T (5KG)
Feature
Tension and compression can be used bothHigh accuracy with good stability
Hermetically welded/sealed by adhesive inside
Oil-proof, waterproof
Variety of capacity for your choice ,500KG measuring range is 0 to 500KG
Description
Note: The color of the item may vary slightly due to photography and your own computerDescription
The item is made of alloy steel, hermetically welded/sealed by adhesive inside,oil-proof, waterproof and anti-corrosion.Safe and anti-explosive product, can be used in atrocious environment and hazardous areas. It is suitable for crane scale, mechanical conversion scale, hopper scale and other electronic weighing devices.S beam design,tension and/or compression loading possible,easy installation Sensitivity2.00.05mV/V Nonlinear0.03%FS Hysteresis0.03%FS Zero output1%FS Output resistance: 350 5hm Insulation resistance: More than 5000megohm50VDC Input resistance: 365 20 ohm Excitation voltage10V-15V Size:3x0.75x2inch Connection mode: red: power supply +, black: power -, green: signal + white: signal - Package Included: 1x Load cell6. Uxcell a15072900ux0605 4 Piece Weighing Sensor Resistance strain Half-bridge, Total 20 kg
Feature
Product name : half bridge weigh sensor; total rated load : 4x5kg;overallprecision : 1.0+/-0.1Mv/v; none linearilty : 0.08 percentInput resistance : 1000+/-20 ohm
Out resistance : 1000+/-20 ohm; insulation resistance : 3000M ohm(50v);safety overload : 120 percent ro; ultimate overload : 150 percent or
Zero balance : +/-1 percent excitation voltage : dc 5V;total size : 28x24x4.8Mm/0.09ftx0.08ftx0.015Ft(l x w x t);material : aluminum alloy
Color : silver tone; weight : 18G;package content : 4Pcs x half bridge weigh sensor
Description
Used widely in hopper scales, platform scales, platform balance, belt scales and other electronic weighing devices. this is a half-bridge load sensor, which is widely used in weight scales. When the half-bridge is being stretched, it sends signal via the red signal wire. You can use multiple load sensors simultaneously to increase the capacity range. Two sensors full-bridge measurements: 5kgx2=10kg four sensor full-bridge measurements: 5kgx4=20kg parallel use to add additional capacity.7. KNACRO HX711 ADC Converter Breakout Module Digital Load Cell Weight Sensor 10KG Portable Electronic Kitchen Scale, DIYmall for Load Cell Weight Weighing (10 Kg)
Feature
HX711 module uses 24 high precision A/D converter chip hx711;HX711 a specially designed for the high precision electronic scale design with two analog input channelthe internal integration of 128 times the programmable gain amplifier.
On-chip active low noise PGA with selectable gain of 3264 and 128 .
On-chip power supply regulator for load-cell and ADC analog power supply .
On-chip oscillator requiring no external component with optional external crystal .
Description
Two selectable differential input channels .On-chip active low noise PGA with selectable gain of 3264 and 128 .
On-chip power supply regulator for load-cell and ADC analog power supply .
On-chip oscillator requiring no external component with optional external crystal .
On-chip power-on-reset .
Simple digital control and serial interface: pin-driven controlsno programming needed .
Selectable 10SPS or 80SPS output data rate .
Simultaneous 50 and 60Hz supply rejection .
Current consumption including on-chip analog power supply regulator: normal operation < 1.5mApower down < 1uA .
Operation supply voltage range: 2.6 ~ 5.5V .
Operating Temperature Range:-20 degree ~ +85 degree .
Connection:
Red to E+
Black to E-
Green to A+
White to A-
Package Included:
1*HX711 ADC Converter Breakout Module
If you have any question , please feel free to contact us.
Feedback:
We greatly appreciate your POSITIVE feedback. Please do NOT leave negative feedback without asking for help. Our aim is to provide Top Level Customer Service, so we will try our best to solve any problem.Thank you very much!
8. NOYITO 1kg 5kg 10kg 20kg Load Cell and HX711 Combo Pack Kit - Load Cell Amplifier ADC Weight Sensor for Arduino Scale (10kg+HX711)
Feature
Load cellSturdy aluminum alloy construction with strain gauges pre-attached with strain relieved wires. Accurate measures forces from 0-5kg/ 5kg /10kg /20kg.HX711 :This top of the line load cell amplifier mounted on a breakout board pairs perfectly with the load cell to provide fast, accurate force measurements. It measures small changes in the resistance of the strain gauges mounted to the load cell and passes these values directly to any micro controller (like an Arduino or Raspberry Pi).
Load cell specs: 22 cm (8.5 in) wire leads pre-attached. Dimensions 12.7 mm high, 12.7 mm wide, 80 mm long (0.5 in x 0.5 in x 3.15 in). 4 mounting holes, 15 mm spacing on each side. One both holes tapped M4 thread, the other side both holes tapped M5 thread.
HX711 specs: Operation Voltage: 2.7V-5V ; Operation Current: < 1.5mA ; Selectable 10SPS or 80SPS output data rate ; Includes breakaway headers for connection, soldering required.
Please choose the correct specification before buying. (A total of four specifications).Please refer to the picture on the left of this page for the product wiring diagram.
Description
DescriptionLoad cell - Sturdy aluminum alloy construction with strain gauges pre-attached with strain relieved wires. Accurately measures forces from 0-5kg/ 5kg /10kg /20kg.
HX711 - This top of the line load cell amplifier mounted on a breakout board pairs perfectly with the load cell to provide fast, accurate force measurements. It measures small changes in the resistance of the strain gauges mounted to the load cell and passes these values directly to any microcontroller (like an Arduino or Raspberry Pi).
HX711 specs:
Operation Voltage: 2.7V-5V
Operation Current: < 1.5mA
Selectable 10SPS or 80SPS output data rate
Mounted on breakout board
-ncludes breakaway headers for connection, soldering required
Connections:
Red wire to E+
Black wire to E-
Green wire to A+
White wire to A-
Package Included:
1xLoad Cell and HX711 Combo Pack Kit
9. uxcell 10kg Portable Accuracy Electronic Scale Weighing Sensor Load Cell
Feature
Product Name : Load Cell;Rated Load : 10kg;Rated Output : 10MV/V;Zero Output : +/-1.0%F.SOverall Precision : +/-0.02%F.S;Precision Temperature : +/-0.02%F.S;Working Temperature : -30 ~ +40C;Compensated Temperature Range : -10 ~ +40C
Safety Overload : 120%F.S;Recommend Excitation Voltage : 5V(DC);Max Excitation Voltage : 10V(DC);Total Size : 32 x 8.5 x 1mm/1.3" x 0.3" x 0.04"
Thead Hole Diameter : 4mm/0.16";Cable Length : 11.5cm;Material : Aluminium Alloy
Color : Silver;Weight : 4.2g;Package Content : 1 x Load Cell
Description
Specifications: Descriptions:Used widely in hopper scales, platform scales, platform balance, belt scales and other electronic weighing devices.
10. KNACRO HX711 ADC Converter Breakout Module Digital Load Cell Weight Sensor 10KG Portable Electronic Kitchen Scale, DIYmall for Load Cell Weight Weighing
Feature
HX711 module uses 24 high precision A/D converter chip hx711;HX711 a specially designed for the high precision electronic scale design with two analog input channelthe internal integration of 128 times the programmable gain amplifier.
On-chip active low noise PGA with selectable gain of 3264 and 128 .
On-chip power supply regulator for load-cell and ADC analog power supply
On-chip oscillator requiring no external component with optional external crystal .
Description
HX711 module uses 24 high precision A/D converter chip hx711;HX711 a specially designed for the high precision electronic scale design with two analog input channelthe internal integration of 128 times the programmable gain amplifier.
On-chip active low noise PGA with selectable gain of 3264 and 128 .
On-chip power supply regulator for load-cell and ADC analog power supply .
On-chip oscillator requiring no external component with optional external crystal .
Features:
Two selectable differential input channels .
On-chip active low noise PGA with selectable gain of 3264 and 128 .
On-chip power supply regulator for load-cell and ADC analog power supply .
On-chip oscillator requiring no external component with optional external crystal .
On-chip power-on-reset .
Simple digital control and serial interface: pin-driven controlsno programming needed .
Selectable 10SPS or 80SPS output data rate .
Simultaneous 50 and 60Hz supply rejection .
Current consumption including on-chip analog power supply regulator: normal operation < 1.5mApower down < 1uA .
Operation supply voltage range: 2.6 ~ 5.5V .
Operating Temperature Range:-20 degree ~ +85 degree .
Connection:
Red to E+
Black to E-
Green to A+
White to A-
Package Included:
1*HX711 ADC Converter Breakout Module
