When you looking for ublox m8, you must consider not only the quality but also price and customer reviews. But among hundreds of product with different price range, choosing suitable ublox m8 is not an easy task. In this post, we show you how to find the right ublox m8 along with our top-rated reviews. Please check out our suggestions to find the best ublox m8 for you.
Reviews
1. DIYmall Micro GPSV5 NEO-M8N GPS Module GNSS HMC5983 Saw LNA Triple Band Antenna ANT
Feature
Main chip:u-blox M8 VCC to 3.3V or 5V, voltage is 3V-5VWhat you will get: 1pcs NEO-M8N GPS module ,1pcs antenna, 1pcs cable
Warranty:lifetime warranty,we offer free gift to anyone who want to make project,please contact
Description
NEO-M8N breakout board features:72-channel u-blox M8 engine GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1 SBAS L1 C/A: WAAS, EGNOS, MSAS Galileo-ready E1B/C (NEO-M8N) SuperSense Indoor GPS, -167dBm
On-board Ultra low noise 3.3V voltage regulator and RF filter for noise blocking
I2C (SDA,SCL) and Uart (Tx,Rx)
Triple band GPS, Glonass and BeiDou antenna
Triple band Band Pass filter
Triple Band LNA
u-center GPS Evaluation Software
Extensive visualization and evaluation features
Supports AssistNow Online and AssistNow Offline A-GPS services
1 TTL UART port, 1 I2C port
Time pulse LED
Battery for HOT module start and settings storage
Build-in HMC5983 Compass
Dimensions: 33*33mm hole distance 22x22mm
Weight 8.5 gram
Fully assembled and ready to use
Connection:
vcc----- 3.3V or 5V
rx-------tx
tx-------rx
gnd-----gnd
Package Included:
1 X GPSV5 NEO-M8N GPS Module
1 X GA25F3-60U Antenna
2. Geekstory U-G8030-KT GPS Receiver Module Compatible with NEO-M8N for Betaflight Flight Control APM Pixhawk CC3D Naze32 Aircraft
Feature
This gps module, without a compass, has UBX high sensitivity solutionNMEA 0183 standard output, Fast TTFF at low signal level
Incorporated external LNA and SAW filter realize high-sensitivity and noise immunity
The GPS Module don't have flash. It can not save your setting.
This gps module, with U-G8030-KT chip for ublox gps, is compatible with NEO-M8N
Description
NOTE: This module without a compassSpecification:
Item name: U-M8N GPS
Weight: 10g
Size18*18MM
Features:
1. NMEA 0183 standard output
2. Fast TTFF at low signal level
3.RoHS compliant (Lead-free)
4. UBLOX high sensitivity solution
5. Jamming detection and mitigation
6. Multi-path detection and compensation
7. Built-in 12 multi-tone active interference canceller
8. Free hybrid ephemeris prediction to achieve faster cold start
9. Supports GPS, SBAS (WAAS, EGNOS, MSAS, GAGAN) and QZSS
10. Incorporated external LNA and SAW filter realize high-sensitivity and noise immunity
11. Integrated high sensitivity passive Patch Antenna, Size:18(w)mmX18(d)mmX4(h)mm
Package Includes:
1 X GPS module
1 X 4P wire
3. Readytosky M8N GPS Module Built-in Compass Protective Case with GPS Antenna Mount for Standard Pixhawk 2.4.6 2.4.8 Flight Controller
Feature
Special designed for Pixhawk 2.4.6 2.4.8 flight controller,ASIN:B07CHQ7SZ4.(Note:If you use it to APM Flight Controller, Please replace the connect by yourself.)The ultimate accuracy is 0.6 meters, actually almost 0.9 meters, greater than the previous generation NEO-7N 1.4-1.6 meters accuracy.
A new generation M8N GPS,with low power consumption and high precision.
The GPS light only can light up when it search the satellite signal outdoor; ROM already been fix,it cannot be flash and change.
Attention: the GPS can only use in Pixhawk and APM Flight controller,it can't work with other flight controller.
Description
GPS Specs:- Receiver type 72-channel u-blox M8 engine
- GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1
- SBAS L1 C/A: WAAS, EGNOS, MSAS
- Galileo-ready E1B/C (M8N)
- Nav. update rate1 Single GNSS: up to 18 HZ
- Concurrent GNSS: up to 10 Hz
- Position accuracy2 2.0 m CEP
- Acquisition2 Cold starts: 26 s
- Aided starts: 2 s
- Reacquisition: 1.5 s
- Sensitivity2 Tracking & Nav: -167 dBm
- Cold starts: -148 dBm
- Hot starts: -156 dBm
- Assistance AssistNow GNSS Online
- AssistNow GNSS Offline (up to 35 days)3
- AssistNow Autonomous (up to 6 days)
- OMA SUPL & 3GPP compliant
- Oscillator TCXO ,
- Crystal
- RTC crystal Built-In
- Noise figure On-chip LNA . Extra LNA for
- lowest noise figure
- Anti jamming Active CW detection and removal. Extra
- onboard SAW band pass filter
- Memory ROM or Flash
- Supported antennas Active and passive
- Odometer Travelled distance
- Data-logger For position, velocity, and time
- Operating temp. -40 C to 85 C
- Storage temp. -40 C to 85 C
- -40 C to 105 C
- RoHS compliant (lead-free)
Package includes
1xM8N GPS Module Built-in Compass
- 1x Black GPS Holder
Important:
The GPS light only can light up when it search the satellite signal outdoor.
ROM already been fixit cannot be flash and change.We left a connector for APM extra,If you need used for APM, you can install the connector by yourself.
4. Hobbypower NEO-M8N GPS Module with Compass + GPS Folding Antenna Mount Holder for APM2.8 APM 2.6 Pixhawk PX4 Flight Controller
Feature
GPS NEO-M8N with low power consumption and high precision, the ultimate accuracy is 0.6 meters, actually almost 0.9 meters, greater than the previous generation NEO-7N 1.4-1.6 meters accuracy,support GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1 protocol and mode or more.Receiver type 72-channel u-blox M8 engine
Built-in compass;It supported antennas Active and passive
Default 5P plug for APM , and comes with a 6P plug ,you can change it for Pixhawk .
If you use the Pixhawk flight controller,you need to add the 6pin connector as picture shows,and when you use and calibrate the compass if you connect to the APM flight controller,you need to remove the jumper wire on APM.
Description
GPS Specs:- Receiver type 72-channel u-blox M8 engine
- GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1
- SBAS L1 C/A: WAAS, EGNOS, MSAS
- Galileo-ready E1B/C (NEO-M8N)
- Nav. update rate1 Single GNSS: up to 18 HZ
- Concurrent GNSS: up to 10 Hz
- Position accuracy2 2.0 m CEP
- Acquisition2 Cold starts: 26 s
- Aided starts: 2 s
- Reacquisition: 1.5 s
- Sensitivity2 Tracking & Nav: -167 dBm
- Cold starts: -148 dBm
- Hot starts: -156 dBm
- Assistance AssistNow GNSS Online
- AssistNow GNSS Offline (up to 35 days)3
- AssistNow Autonomous (up to 6 days)
- OMA SUPL & 3GPP compliant
- Oscillator TCXO (NEO-M8N/Q),
- Crystal (NEO-M8M)
- RTC crystal Built-In
- Noise figure On-chip LNA (NEO-M8M). Extra LNA for
- lowest noise figure (NEO-M8N/Q)
- Anti jamming Active CW detection and removal. Extra
- onboard SAW band pass filter (NEO-M8N/Q)
- Memory ROM (NEO-M8M/Q) or Flash (NEO-M8N)
- Supported antennas Active and passive
- Odometer Travelled distance
- Data-logger For position, velocity, and time (NEO-M8N)
- Operating temp. -40 C to 85 C
- Storage temp. -40 C to 85 C (NEO-M8N/Q)
- -40 C to 105 C (NEO-M8M)
- RoHS compliant (lead-free)
Package includes
1x Ublox NEO-M8N GPS Module Built-in Compass
1x GPS bracket Important note:If you use the Pixhawk flight controller,you need to add the 6pin connector as picture shows,and when you use and calibrate the compass if you connect to the APM flight controller,you need to remove the jumper wire on APM.
Please contact me if there is an issue with ths GPS unit,thank you.
5. Vanpower APM2.5 Ublox GYGPSV1 NEO-M8N GPS Module MWC Replace NEO-6M GY-NEO8MV2
Feature
Module with ceramic active antenna.With data backup battery.
LED signal indicator.
Compatible with various flight controller module.
EEPROM save the configuration parameter data when power-down.
Description
Specifications:Antenna Size: approx. 25*25mm/0.98*0.98"
Module Size: approx. 25*32*6mm/0.98*1.25*0.23"
Net weight: approx. 6g
Gross weight: approx. 8g
Mounting: approx. 3mm
The default baud rate: 9600
Note:
It is manual measurement, there may be 2-3mm error. And item color displayed in photos may be showing slightly different on your computer monitor since monitors are not calibrated same.hope understanding.
Package Content:
1 x APM2.5 Ublox GYGPSV1 NEO-M8N GPS Module
6. Icstation NEO-M8N GPS Module Triple Band TTL Port with Acitive Antenna for Arduino STM32 C51 Replace NEO-6M
Feature
Equipped with upgraded NEO-M8N triple band GPS receiver chip with SMA and IPEX dual antenna port, higher postioning accuracy than NEO-6MOn-board EEPROM support power memory function saving the baud rate and frame data
On-board cell button battery to speed up warm start satellite finding speed, Serial port output the GPS data easy to communicate with arduino STM32 MCU
Baud Rate: 9600(settable),Output Frequency:1Hz(settable),Compatible satellite System:GPS,Beidou(BDS),GLONASS
Comes with ceramic active antenna with 30dB gain suppporting GPS/BDS/GLONASS system
Description
This is the upgraded GPS module equipped with orignal UBLOX NEO-M8N triple band receiver chip higher postioning accuracy than NEO-6M.It has EEPROM and spare cell battery with power memory function ensure stable positioning performance and fast satellite finding speed.TTL serial communication port output the initial data easy to communicate the MCU perfect compatible with Arduino STM32 C51 mainboard.7. Geekstory BN-180 GPS Module U-M8030-KT UART TTL Dual Glonass GPS Car Navigation + GPS Antenna for Arduino Raspberry Pi Pixhawk Aircraft CC3D F3 Flight Controller
Feature
This BN-180 GPS Module can show your speed. When you use it for Raspberry Pi, there is no driver needed.The TX LED flash means gps module output normally.The PPS LED flash means gps module locate your place
With U- M8030-KT chip for ublox gps, 72 Searching Channel Support Rate : 4800bps to 921600bps,Default 9600bps
Data Level : TTL or RS-232,Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable
Data Protocol : NMEA-0183 or UBX, Default NMEA-0183
Description
DescriptionDimension :18mm*18mm*6mm
Weight : 4.9g
Connector : 1.00mm spacing between the 4pins patch seat
Specification
Electrical Characteristics
Chipset : u-M8030-KT
Receiving Format :GPS,GLONASS,Galileo,BeiDou,QZSS and SBAS
Frequency : GPS L1,GLONASS L1,BeiDou B1,SBAS L1,Galileo E1
Channels : 72 Searching Channel
Sensitivity
Tracking : -167dBm
Reacquisition : -160dBm
Cold start : -148dBm
Hot start : -156dBm
Accuracy
Position Horizontal : 2.0 m CEP 2D RMS SBAS Enable (Typical Open Sky)
Velocity : 0.1m/sec 95% (SA off)
Timing : 1us synchronized to GPS time
Acquisition Time
Cold Start : 26s
Warm start : 25s
Hot start : 1s
Data and Update Rate
Support Rate : 4800bps to 921600bps,Default 9600bps
Data Level : TTL or RS-232,Default TTL level
Data Protocol : NMEA-0183 or UBX, Default NMEA-0183
Single GNSS : 1Hz-18Hz
Concurrent GNSS : 1Hz-10Hz,Default 1Hz
Operational Limits
Altitude : 50,000m Max
Velocity : 515m/s Max
Acceleration : Less than 4g
Power consumption
VCC : DC Voltage 3.0V-5.5V,Typical: 5.0V
Current : Capture 50mA/5.0V
Operating temp :-40 C ~ +85C
Storage Temp : -40C ~ +105C
Indicator :
TX LED:blue.The data output, TX LED flashing
PPS LED:red.PPS LED not bright when GPS not fixed,flashing when fixed
Wiring:
GND,TX output,RX input,VCC(3.0v-5.5v)
Package Included
1 x BN-180 GPS Module
2 x 15cm Cable
8. Beitian BN-800 U-M8030-KT TTL GPS Module Car Navigation with HMC5883 Compass Flash +GPS Passive Antenna Support Glonass BeiDou for Arduino Raspberry Pi Aircraft Pixhawk APM Flight Controller Geekstory
Feature
This bn-800 gps has the newest U-M8030-KT chipset for ublox gps. Output frequency is 1Hz-10Hz but 1Hz default.When you use it for Arduino Raspberry Pi, there is no driver needed but you need to install u-center software.
This gps module has flash. So you can save configuration, and do not need to reset next time when you use it.
The TX LED flash means gps module output normally.The PPS LED flash means gps module locate your place.
Its data Level is TTL or RS-232,Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable
Description
Description:Chipset : u-M8030-KT
Power Supply:DC Voltage 2.8V~6.0V,Typical:3.3V or 5.0V
Consumption:Capture 50mA@5V
Receiving Format: GPS,GLONASS,Galileo,BeiDou,QZSS and SBAS
Receiving Channel:72 Searching Channel
Receiving Sensitivity:Trace -167dBm,Capture-148dBm
Positioning Time:Cold Start: avg26s,Warm Start: avg25s,Hot Start: avg3s
Level Positioning Precision: 2m At Open Wind
Output Frequency:1Hz-10Hz,Default 1Hz
Speed Precision: 0.1 m/s (Without Aid)
Acceleration Precision: 0.1 m/s (Without Aid)
Dynamic Characteristics:Max Height:18000m,Max Speed:515m/s,Max Acceleration:4G
UART Interface:UART Port:TXDA and RXDA
Support Rate:4800bps to 115200bps,Default 9600dps
Working Temperature:-40-+85
Mounting Distance : 30x30mm
Hole Dia. : R1.7mm
Features:
With U-blox M8
Can simultaneously acquire and track different GNSS (Global Navigation
Satellite) system,parallel to receive GPS (QZSS) and GLONASS or BeiDou, or while receiving GLONASS and BeiDou. Specially adapted to the needs to the highest availability and accuracy of high-performance applications, even if is in the GPS signal poor environment.
Equipped with a built-in intelligent automatic switching function.
With long Offline A-GNSS (GPS and GLONASS) function.
Can run simultaneously GPS + GLONASS or GPS +BeiDou
With GPS antenna
Low power consumption
Fast positioning speed
Search to more number of satellites and high positioning accuracy
Notice:
Cable supports mini APM, if it is used for version 2.6 or 2.8,GPS of Pixhawk is needed to change the cable by yourself.
Can not use for flight control with SCM, but it is also suitable for Open source flight controller.
Package Included:
1 x BN-800 GPS Module
1 x Cable
9. Readytosky M8N GPS Module Built in Compass for F4 Omnibus V2/V3 Pro Flight Controller Board with Foldable GPS Bracket Holder
Feature
M8N GPS With Compass specially for F4 OMNIBUS V3 Pro / FLIP 32 OMNIBUS F4 V2 PRO flight controller board.With low power consumption and high precision.
Built-in Compass.With foldable gps stand,very convenient to use.
The M8N GPS firmware is fixed,so it is no need to revise firmware after you recieved.If you mind,please do not buy.
Attention:special for F4 OMNIBUS V2/ V3 Pro flight controller,if you use with other flight controller,it may can't work well!!!
Description
GPS Chip parameters:Receiver type 72-channel u-blox M8 engine
GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1
SBAS L1 C/A: WAAS, EGNOS, MSAS
Galileo-ready E1B/C (NEO-M8N)
Nav. update rate1 Single GNSS: up to 18 HZ
Concurrent GNSS: up to 10 Hz
Position accuracy2 2.0 m CEP
Acquisition2 Cold starts: 26 s
Aided starts: 2 s
Reacquisition: 1.5 s
Sensitivity2 Tracking & Nav: -167 dBm
Cold starts: -148 dBm
Hot starts: -156 dBm
Assistance AssistNow GNSS Online
AssistNow GNSS Offline (up to 35 days)3
AssistNow Autonomous (up to 6 days)
OMA SUPL & 3GPP compliant
Oscillator TCXO (NEO-M8N/Q),
Crystal (NEO-M8M)
RTC crystal Built-In
Noise figure On-chip LNA (NEO-M8M). Extra LNA for lowest noise figure (NEO-M8N/Q)
Anti jamming Active CW detection and removal. Extra onboard SAW band pass filter (NEO-M8N/Q)
Memory ROM (NEO-M8M/Q) or Flash (NEO-M8N)
Supported antennas Active and passive
Odometer Travelled distance
Data-logger For position, velocity, and time (NEO-M8N)
Operating temp. -40 C to 85 C
Storage temp. -40 C to 85 C (NEO-M8N/Q)
-40 C to 105 C (NEO-M8M)
RoHS compliant (lead-free)
Qualification according to ISO 16750
Manufactured and fully tested in ISO/TS 16949 certified production sites
Uses u-blox M8 chips qualified according to AEC-Q100
Supply voltage 1.65 V to 3.6 V (NEO-M8M)
2.7 V to 3.6 V (NEO-M8N/Q)
Power consumption4 23 mA @ 3.0 V (continuous)
5 mA @ 3.0 V Power Save Mode
(1 Hz, GPS mode only)
Backup Supply 1.4 to 3.6 V
NEO-M8N-0 u-blox M8 Concurrent GNSS LCC Module,
TCXO, flash, SAW, LNA,
Timepulse Configurable 0.25 Hz to 10 MHz
Package included:
1 x M8N GPS Module with Shell
Note: This M8N GPS is only used for F4 OMNIBUS V2 / V3 PRO Flight controller board.
10. G28U7FTTL Replace VK16E Gmouse GPS Navigation Module U-G7020-KT GPS Ceramic Antenna TTL Level 9600bps Arduino Aircraft Flight Control Geekstory
Feature
This gps uses about half the power of comparable NEO 6 modules, but has comparable satellite tracking ability and slightly faster lock times. It's smaller than any other unit with a 25x25x4mm patch antenna. And the shield covering nearly the entire circuit board reduces RF interference with nearby radio receivers.The location data is very accurate. It is even able to pinpoint correct location its located within your house.
It has PPS outpu, for ublox G7020-KT chip, built-in LNA signal amplifier, and 1-10Hz positioning update rate
Built-in LNA signal amplifier. Also, it has built-in flash. You can free save configuration of parameters.
Baud rate:4800,9600,19200,38400,57600,112500bps9600 default)
Description
Description:Product main chip: for ublox G7020-KT
Built-in LNA signal amplifier
Built-in Flash, free configuration of product parameters
Industry-standard 25 x 25 x 4mm high-sensitivity ceramic antenna
Built-in TCXO crystal and Farah capacitor faster hot start
1-10Hz positioning update rate
Frequency: L1, 1575.42MHz
Baud rate: 4800,9600,19200,38400,57600,112500bpsdefault baud rate is 9600)
Channel: 56
Sensitivity tracking: -162dBm Capture: -160dBm cold start -148dBm
Cold start averages: 29 seconds
Warm start averaging: 28 seconds
Hot start averages: 1 second
Precision: HorizontalPosition: Autonomous <2.5maverage
SBAS <2.0m average
Timepulse signal: RMS 30 ns
Maximum height: 50000 meters
Maximum speed: 500 m / s
Maximum acceleration: 4G
Update frequency: 1-10 Hz
Dimensions 28 x 28 x 8.5 mm
Weight: 30 grams
Operating temperature -40 to 85 degree celsius
Storage temperature -40 to 85 degree celsius
Application:
It can be used in vehicle monitoring, bus station, car guide
Navigation, ship navigation, notebook navigation and other products
google link: https://drive.google.com/file/d/0B8DSGdAr8_31bUdiMWJacjd5X0U/view?usp=sharing
Package Included:
1 X G28U7FTTL Replace VK16E GMOUSE GPS Module
1 X cable
