If you looking for flat belt drive then you are right place. We are searching for the best flat belt drive on the market and analyze these products to provide you the best choice.
Reviews
1. Fenner Drives FA3002 PowerMax Flat Belt Idler, 1" Section, Glass Reinforced Nylon, 17 mm Bore, 3" OD
Feature
Suitable for use as back side idlers on V beltsThe molded-in crown helps center the belt
Helps prevent rubbing against the outside flanges
Lighter-weight composite design means less energy for start up and running
Description
Flat Belt Idler for use with Self Adjusting Belt tensioner and to guide the belt or chain.2. Gates B99 Hi-Power II Belt, B Section, B99 Size, 21/32" Width, 13/32" Height, 102.0" Belt Outside Circumference
Feature
EPDM for resistance to weathering, oils, water, and some solventsCords bonded to the body for equal load distribution and reduced bending stress
Concave sidewalls for even distribution of wear
V80 matching program for precisely-matched sizes in varying belt types
Meets RMA oil and heat resistance standards and static conductivity requirements
Description
This Gates Hi-Power II belt is a multipurpose power transmission V-belt for widespread applications. It is made of EPDM (ethylene propylene diene monomer) rubber for resistance to weathering, oils, water, and some solvents. Its cords are bonded to the body are strongly bonded to the body of the belt for equal load distribution and reducing bending stress without deterioration of the cord. Its concave sidewalls provide cord support and full contact with the sheave groove for equal loading and uniform wear. Hi-Power II belts are part of Gates' V80 matching system, which guarantees that all belts of the same type and size will be more precisely matched than the Rubber Manufacturers Association (RMA) and International Standards Organization (ISO) standards require. The result is even load distribution on multi-belt drives and better wear. This V-belt meets RMA oil and heat resistance standards and static conductivity requirements and is suitable for use in all industrial applications, including V-flat drives.
V-belts, also calledfan belts in automotive applications, link two or more rotating shafts to transmit power in a drive system. The trapezoidal shape of the belt's cross section wedges into the groove of a similarly shaped sheave or pulley to provide traction and alignment. This wedging action increases as the load increases, providing higher torque transmission and minimal slippage. V-belts are standard for belt-driven power transmission and can be used in single- or multi-belt systems for increased carrying power. They are found in drive systems in the automotive, agricultural, textile, printing, mining, and office equipment industries, among others.
Gates manufactures power transmission and fluid transfer components and systems. The company, founded in 1917, is headquartered in Denver, CO.
3. Fenner Drives FA3251 PowerMax Flat Belt Idler, 1" Section, Glass Reinforced Nylon, 17 mm Bore, 3.24" OD
Feature
Suitable for Use as back side idlers on V beltsThe molded-in crown helps center the belt
Helps prevent rubbing against the outside flanges
Lighter-weight composite design means less energy for Start up and running
Description
Flat belt idler for use with self adjusting belt tensioner and to guide the belt or chain.4. Gates A64 Hi-Power II Belt, A Section, A64 Size, 1/2" Width, 5/16" Height, 66.0" Belt Outside Circumference
Feature
EPDM for resistance to weathering, oils, water, and some solventsCords bonded to the body for equal load distribution and reduced bending stress
Concave sidewalls for even distribution of wear
V80 matching program for precisely-matched sizes in varying belt types
Meets RMA oil and heat resistance standards and static conductivity requirements
Description
This Gates Hi-Power II belt is a multipurpose power transmission V-belt for widespread applications. It is made of EPDM (ethylene propylene diene monomer) rubber for resistance to weathering, oils, water, and some solvents. Its cords are bonded to the body are strongly bonded to the body of the belt for equal load distribution and reducing bending stress without deterioration of the cord. Its concave sidewalls provide cord support and full contact with the sheave groove for equal loading and uniform wear. Hi-Power II belts are part of Gates' V80 matching system, which guarantees that all belts of the same type and size will be more precisely matched than the Rubber Manufacturers Association (RMA) and International Standards Organization (ISO) standards require. The result is even load distribution on multi-belt drives and better wear. This V-belt meets RMA oil and heat resistance standards and static conductivity requirements and is suitable for use in all industrial applications, including V-flat drives.
V-belts, also calledfan belts in automotive applications, link two or more rotating shafts to transmit power in a drive system. The trapezoidal shape of the belt's cross section wedges into the groove of a similarly shaped sheave or pulley to provide traction and alignment. This wedging action increases as the load increases, providing higher torque transmission and minimal slippage. V-belts are standard for belt-driven power transmission and can be used in single- or multi-belt systems for increased carrying power. They are found in drive systems in the automotive, agricultural, textile, printing, mining, and office equipment industries, among others.
Gates manufactures power transmission and fluid transfer components and systems. The company, founded in 1917, is headquartered in Denver, CO.
5. Hoover Belt, Flat Power Drive Type 170 Wind Tunnel (Pack of 2)
Feature
This is an O E M authorized partFits various Hoover models
OEM Part Number 40201170
This is a Bissell replacement part
Part Number 40201170
This is an O E M part
Vacuum belts for WindTunnel vacuums U5395-900 (2940-0849)
Flat belt
2 belts per pack
Hoover Brand Product
Easy to Use
Description
This is an O.E.M. authorized part. Fits various Hoover models. OEM Part Number 40201170. Made in United States.6. Fenner Drives FA3750 PowerMax 1" Flat Belt Idler, Glass Reinforced Nylon, 3.75" OD, 17 mm Bore
Feature
Suitable for Use as back side idlers on V beltsThe molded-in crown helps center the belt
Helps prevent rubbing against the outside flanges
Lighter-weight composite design means less energy for Start up and running
Description
Flat belt idler for use with self adjusting belt tensioner and to guide the belt or chain.7. Jason Industrial 54.0M100 Type 400 Endless Woven Flat Belt, Polyester, 54" Long, 1.00" Wide
Feature
Oil-resistant, non-marking cover Static conductiveSingle Ply
Endless woven polyester cord
Description
Jason Type 400 flat belts are single-ply, endless woven belts built to the rigid standards necessary to meet the demands of modern high speed compact drives requiring flat belts. These belts are interchangeable with Gates Speed Flex, #400 Panther, Tilton Super speed and Fenner Ultra Speed 400. These high-performance flat belts have a single-ply of endless woven polyester cord bonded to an oil-resistant, non-marking, static conducting chloroprene (Neoprene) rubber covers.
8. Gates B45 Hi-Power II Belt, B Section, B45 Size, 21/32" Width, 13/32" Height, 48.0" Belt Outside Circumference
Feature
EPDM for resistance to weathering, oils, water, and some solventsCords bonded to the body for equal load distribution and reduced bending stress
Concave sidewalls for even distribution of wear
V80 matching program for precisely-matched sizes in varying belt types
Meets RMA oil and heat resistance standards and static conductivity requirements
Description
This Gates Hi-Power II belt is a multipurpose power transmission V-belt for widespread applications. It is made of EPDM (ethylene propylene diene monomer) rubber for resistance to weathering, oils, water, and some solvents. Its cords are bonded to the body are strongly bonded to the body of the belt for equal load distribution and reducing bending stress without deterioration of the cord. Its concave sidewalls provide cord support and full contact with the sheave groove for equal loading and uniform wear. Hi-Power II belts are part of Gates' V80 matching system, which guarantees that all belts of the same type and size will be more precisely matched than the Rubber Manufacturers Association (RMA) and International Standards Organization (ISO) standards require. The result is even load distribution on multi-belt drives and better wear. This V-belt meets RMA oil and heat resistance standards and static conductivity requirements and is suitable for use in all industrial applications, including V-flat drives.
V-belts, also calledfan belts in automotive applications, link two or more rotating shafts to transmit power in a drive system. The trapezoidal shape of the belt's cross section wedges into the groove of a similarly shaped sheave or pulley to provide traction and alignment. This wedging action increases as the load increases, providing higher torque transmission and minimal slippage. V-belts are standard for belt-driven power transmission and can be used in single- or multi-belt systems for increased carrying power. They are found in drive systems in the automotive, agricultural, textile, printing, mining, and office equipment industries, among others.
Gates manufactures power transmission and fluid transfer components and systems. The company, founded in 1917, is headquartered in Denver, CO.
9. Gates A32 Hi-Power II Belt, A Section, A32 Size, 1/2" Width, 5/16" Height, 34.0" Belt Outside Circumference
Feature
EPDM for resistance to weathering, oils, water, and some solventsCords bonded to the body for equal load distribution and reduced bending stress
Concave sidewalls for even distribution of wear
V80 matching program for precisely-matched sizes in varying belt types
Meets RMA oil and heat resistance standards and static conductivity requirements
Description
This Gates Hi-Power II belt is a multipurpose power transmission V-belt for widespread applications. It is made of EPDM (ethylene propylene diene monomer) rubber for resistance to weathering, oils, water, and some solvents. Its cords are bonded to the body are strongly bonded to the body of the belt for equal load distribution and reducing bending stress without deterioration of the cord. Its concave sidewalls provide cord support and full contact with the sheave groove for equal loading and uniform wear. Hi-Power II belts are part of Gates' V80 matching system, which guarantees that all belts of the same type and size will be more precisely matched than the Rubber Manufacturers Association (RMA) and International Standards Organization (ISO) standards require. The result is even load distribution on multi-belt drives and better wear. This V-belt meets RMA oil and heat resistance standards and static conductivity requirements and is suitable for use in all industrial applications, including V-flat drives.
V-belts, also calledfan belts in automotive applications, link two or more rotating shafts to transmit power in a drive system. The trapezoidal shape of the belt's cross section wedges into the groove of a similarly shaped sheave or pulley to provide traction and alignment. This wedging action increases as the load increases, providing higher torque transmission and minimal slippage. V-belts are standard for belt-driven power transmission and can be used in single- or multi-belt systems for increased carrying power. They are found in drive systems in the automotive, agricultural, textile, printing, mining, and office equipment industries, among others.
Gates manufactures power transmission and fluid transfer components and systems. The company, founded in 1917, is headquartered in Denver, CO.
10. Fenner Drives FA3502 PowerMax Flat Belt Idler, 1" Section, Glass Reinforced Nylon, 17 mm Bore, 3.5" OD
Feature
Suitable for Use as back side idlers on V beltsThe molded-in crown helps center the belt
Helps prevent rubbing against the outside flanges
Lighter-weight composite design means less energy for Start up and running
