Finding your suitable timer relay 5v is not easy. You may need consider between hundred or thousand products from many store. In this article, we make a short list of the best timer relay 5v including detail information and customer reviews. Let’s find out which is your favorite one.
Reviews
1. DC 6V~30V Multifunction Trigger Delay Time Module Switch Control Relay Cycle Timer Digit LED Display Micro USB 5V
Feature
INSTRUCTIONS:wide DC power supply voltage from 6V to 30V, support micro USB 5.0V power supply, very convenient and practical for your use.FEATURE:the module supports reverse input protection, and there is a STOP button for emergency stop function
ADVANTAGE:Added sleep mode, it will automatically turn off display if no operation in 5 minutes after enabled, and you can press any button to wake it up
PARAMETERS SAVE SEPARATELY:you can set different OP, CL, LOP parameters, these parameters were independent of each other and saved respectively.
LOAD CAPACITY: DC 30V 5A, AC 220V 5A;Operating Temperature: -40~85.
Description
Voltage: 6V~30V(support micro USB 5.0V)
Trigger Signal Source: High voltage level trigger(3.0V~24V), signal ground and system ground are not connected to improve system anti-interference ability(or you can connect them).
Load Capacity: DC 30V 5A, AC 220V 5A
Quiescent Current: 20mA
Operating Current: 50mA
Operating Temperature: -40~85
Size: 6.2*3.8*1.7cm / 2.44*1.49*0.67"
Timing Range: 0.1seconds to 999 minutes(continuously adjustable)
Instruction:
Operation Mode:
P1: After triggering signal, switch is connected for "OP" time, then disconnected; within the "OP" time:
P1.1: if trigger signal again, it is invalid.
P1.2: if trigger signal again, restart timing.
P1.3: if trigger signal again, switch is disconnected, stop timing.
P-2: After triggering signal, switch is disconnected for "CL" time, then switch is connected for "OP" time, and disconnect after timing.
P3.1: After triggering signal, switch is connected for "OP" time, then switch is disconnected for "CL" time, and enter loop. If trigger signal during loop, switch is disconnected and stop timing. The loop times (LOP) can be set.
P3.2: After power on, no need trigger signal, switch will be connected for "OP" time, then disconnected for "CL" time, and enter loop. The loop times (LOP) can be set
P-4: Signal holding function. If there is trigger signal, timing will be reset, switch remains connected; when the signal disappears, it will disconnect after "OP" time. During timing, if there is a signal, timing will be reset.
OP: Connect time. CL: Disconnect time. LOP: Loop times(1~999, "---" indicates infinite times)
Package Includes:
1 x Timer Switch Module
2. Willwin 2pcs 5V NE555 Oscillator Delay Adjustable Timer Relay Switch Module 0-10 Second
Feature
The output can be connected to AC 250V 10A DC 30V 10A load.Control voltage: AC 0~250V/max. 10A, DC 0~30V/max. 10A. The operating voltage: 5V DC
Using high-performance timing CPU design. The power indicator LED and switch trigger timing indication LEDs.
The output can be connected to AC 250V 10A DC 30V 10A load. There is the chronopotentiometry regulation time, adjustable from 0 to 10 seconds by default, or by changing the capacitance adjustment time longer.
Applications: Vehicle equipment-delay to prevent car ignition, prevention of high sudden current to burn components and devices.
Description
Features:This is a brand new and high quality delay turn-on module.
Using high-performance timing CPU design.
The power indicator LED and switch trigger timing indication LEDs.
The output can be connected to AC 250V 10A DC 30V 10A load.
There is the chronopotentiometry regulation time, adjustable from 0 to 10 seconds by default, or by changing the capacitance adjustment time longer
Applications: Vehicle equipment-delay to prevent car ignition, prevention of high sudden current to burn components and devices.
Main Chip (NE555):
Timing from microseconds to long hours.
Simple circuit design.
Precision Pulse Generation / Timing.
Adjustable Duty Cycle.
Countless Application and Information Sources.
Specifications:
Module based on: NE555 chip.
Delay modue:delay connect module
Input voltage: DC05V
Control voltage: AC 0~250V/max. 10A, DC
0~30V/max. 10A
The operating voltage: 05V DC (otherwise 12V optional)
Max. load: 2200W
Quantity: 2pcs
Product size: approx.
68*22*18mm/2.67*0.86*0.7"
Net weight: approx. 34g
Note:
Please allow 1-3mm differs due to manual measurement.
Due to the different display and different light, the picture may not reflect the actual color of the item. Thanks for your understanding.
Package Includes:
2 x Delay Relay Module
3. Qianson DC 5V 12V 24V Digital LED Display Infinite Cycle Delay Timer Switch ON/OFF Relay Module (DC 12V)
Feature
Multifunction Relay module , trigger ,cycle ,delay turn off/on .Time adjustable 0.1 second~ 99 Hours adjustable
Load Power: DC 0-30V 10A / AC 0-220V 10A
Working current: 30mA; Working current: 30mA
Size: 65*28*18mm / 2.54"*1.09"*0.7"
Description
Function introduction:Time delay range: T1 and T2 between 0.1 second ~99 hours adjustable.
P1(relay on):when power on, the relay on, delay T1, and the relay off. Give IN a low level, repeat the above function.
P2(relay off):when power on, the relay disconnected, delay T1, and the relay on. Give IN a low level, repeat the above function.
P3(Timing cycle on-off): when power on, the relay on, delay T1, and the relay off, delay T2, the relay on, and then repeat the above condition, cycle times can be adjusted 1-99 times or infinite loop.
P4(Timing cycle off-on): when power on, the relay disconnected, delay T1, and the relay on, delay T2, the relay off, and then repeat the above condition, cycle times can be adjusted 1-99 times or infinite loop.
P5(trigger relay on): when power on, the relay disconnected, triggered the relay on, delay T1, and the relay off. Give IN a low level, repeat the above function.
P6(trigger relay on):when power on, the relay disconnected, triggered the relay disconnected, delay T1, and the relay on. Give IN a low level, repeat the above function.
P7(trigger cycle on-off): when power on, the relay disconnected, triggered the relay on, delay T1, and the relay off, delay T2, and the relay on, and then repeat the above condition, cycle times can be adjusted 1-99 times or infinite loop.
P8(trigger circle off-on): when power on, the relay disconnected, triggered the relay disconnected, delay T1, and the relay on, delay T2, and the relay off, and then repeat the above condition, cycle times can be adjusted 1-99 times or infinite loop.
Parameters:
1. working voltage: DC 12V
2. Load Power: DC 0-30V 10A / AC 0-220V 10A
3. Static current: 15mA
4. Working current: 30mA
5. Service life:100 thousand times
6. Working temperature: -40-85;
7. Size: 65*28*18mm
Package: 1pc x Module
4. KNACRO 1500W DC 5V (5-8V) Automotive Relay Switch, Digital Time Delay Relay Board with Dual-color (Red+Green) LED Display, On-Off Delay Timer Switch Support Cycle of Time for Car Vehicle
Feature
WIDE APPLICATION: KNACRO relay module can be used in timing, delaying, cycle timing, intermittent timing, raft fishing machine, slow-down machine DIY, etc.DUAL DIGITAL TIME DISPLAY: Our digital delay is equipped with dual time display in two different color, clear and convenient for you to check and change the setting.
WIDE TIMING RANGE: KNACRO time relay delay is able to tolerate the widest timing adjusting range: 0-999S/ 0-999M/ 0-999H, available for various application.
SIMPLE WIRING & OPERATION: This relay switch is four-terminal wiring and setting by buttons, easy and simple for everyone to use it.
AUTO STORE FUNCTION: This 12V time delay relay can store the setting automatically. Please wait 6 seconds after finishing setting the data. The data set will be stored automatically after 6 seconds.
Description
WIDE APPLICATION: KNACRO relay module can be used in timing, delaying, cycle timing, intermittent timing, raft fishing machine, slow-down machine DIY, etc.DUAL DIGITAL TIME DISPLAY: Our digital delay is equipped with dual time display in two different color, clear and convenient for you to check and change the setting.
WIDE TIMING RANGE: KNACRO time relay delay is able to tolerate the widest timing adjusting range: 0-999S/ 0-999M/ 0-999H, available for various application.
SIMPLE WIRING & OPERATION: This relay switch is four-terminal wiring and setting by buttons, easy and simple for everyone to use it.
AUTO STORE FUNCTION: This 12V time delay relay can store the setting automatically. Please wait 6 seconds after finishing setting the data. The data set will be stored automatically after 6 seconds.
Product name: Digital time-delay relay
Product specifications: Display panel: 79*43mm; Installation: 71*40*24mm
Power supply: DC 24V
Timing range: 0-999S/ 0-999M/ 0-999H
Functions: Timing, Delaying, Circulation, etc, 18 functions
Max. Power: Max. working current is 10A, max. power is 1500W
Product Functions:
Function 1: This product can be used in timing, delaying, cycle timing, intermittent timing, etc.
Function 2: This product can be used in raft fishing machine, slow-down machine DIY.
Function 3: This product can be used in timing switch machine, timing alarm control board.
Product Includes:
1* Digital Timer Relay
5. KNACRO Voltage Control Relay/Signal timing start/trigger timer/Auto 5V time delay relay/VT2.3 (DC 12V)
Feature
Digital DC voltage detection, control relay outputs, limit 0-99.9V adjustable voltage can be set to exceed the upper limit relay can also be set below the lower limit of the relay can be detected as a voltage switch, battery over-voltage protection, discharge timing and so on.Timer mode can set the relay contact close and release time, the implementation of a single timing loop.
In voltage control mode, it can preset upper and lower voltage values limits.
Set display shut, the minimum current values are 6mA/5V.
The pre-set parameters can be saved after power off.
Description
Timing Range: 0-999 seconds or 0-999 minutes.Voltmeter display range: DC 0-99.9 V.
Voltage detection error: 0.1V.
Operating Power: DC 5~9V.
Relay parameters: *Coil Voltage: DC 5V.
A set of conversion (Open and Close).
Contact load: 10A/277V AC or 10A/30V DC.
Contact resistance: 100m (1A 6VDC).
Mechanical durability: 10 millions.
Electricity durability: > 100,000 (10A-250VAC).
Operating Temperature: -40 ~ 85 degree.
External signal input: 5 to 12V or passive switch.
Size108*50*20mm.
Weight:55g.
Operating modes:
P-1: Timer.
P-2: Delay timer.
P-3: Voltage control relay, on and off control.
P-4: Voltage control Timer- A (Close).
P-5: Voltage control Timer- B (Release).
P-6: Voltage range control relay.
P-7: Voltage range control Timer.
P-8: Set display shut.
Attention:
Do not reverse input voltage polarity!
Use this product to control the high-voltage electrical equipment
must electrical professionals to operatehigh voltage danger!
Wiring must be operated at a power-off state.
Package Included:
1 KNACRO Voltage Control Relay / Signal timing start / trigger timer / Auto 5V time delay relay / VT2.3
1 User manual
6. Time Delay Relay, DROK 5V 12V 24V Delay Controller Board Delay-off Cycle Timer 0.01s-9999mins Trigger Delay Switching Relay Module with LCD Display Support Micro USB 5V Power Supply
Feature
DROK timer delay relay module operating voltage range is DC 6-30V, support micro USB 5.0 V power supply; support high level trigger 3.0v-34v and low level trigger 0v-0.2v; timing range is 0.01s~9999mins, can be continuously adjustable.LCD Display: the relay board is desiged with LCD display, can clearly and directly show the current mode and parameters.
Sleep Mode: without any operation within 5 minutes will close automatically the LCD backlight. Any button can wake up.
Independent Parameters: OP/CL/LOP parameters can be modified and saved, and they are individual.
Auto Save: All setting parameters are automatically saved by power-fail.
Description
Product Parameters:Working voltage: 6V~30V, support micro USB 5.0 V power supply
Working current: 50mA.
Static Current: 15mA
Max. Output load: DC 30V 5A and AC 220V 5A.
Trigger signal source: High level trigger (3.0V~24.0V), low level trigger (0.0V ~0.2V), switching value control (Potential free contact)
Service life: more than 100,000 times
Working temperature: -40-85C
Additional Functions:
a)Automatically hibernation function/ Low power function: In the running interface, long press STOP to open or close automatically sleep function. (L-P selects ON to start the hibernation function, and OFF turns off the hibernation function);
b)Relay function selection: In the operation interface, shortly press STOP, the relay function is started or closed, 'ON' meets the conduction condition and the relay normally turns on, 'OFF' meets the conduction condition and the relay does not turn on; In the 'OFF' state, the system flashes 'OUT'.
c)Parameters view: In the operation interface, short press SET to display the current parameter setting in the system, without affecting the system normal operation.
d)Display content switching: In the P-5 P-6 mode, switch display content (runtime/cycle times) by pressing DOWN.
Package Includes:
1* Time Delay Relay module
7. uniquegoods 5V DC Multifunction Self-lock Relay PLC Cycle Timer Module Delay Time Switch
Feature
Function 1-8 on power-up self-start function 9-18 require high pulse signal (high duration is shorter than 20ms, hereinafter the same) trigger the start.Genuine high quality power relay modules, high power high-voltage transistor, red, blue signal lights
New upgrade version from 8 kinds to 18 kinds functions.can be widely used in a variety of power control type applications.
Top-quality high-voltage power supply modules, discrete power supply before replacing the system more stable and reliable
Load capacity: normally open port maximum load capacity: DC 0-30V/10A, AC 0-250V/10A;normally closed port maximum load capacity: DC 0-28V/10A, AC 0-125V/10A
Description
FRM01 multifunction relay control module, designed specifically for a variety of users with different needs, the use of micro-controller as the primary Control unit, preset 18 kinds of functions, and can be based on user needs,customize and add other specific functions.Dimensions:66mm * 40MM *20MM(L*W*H);Screw size:4*3mm(diameter);Screw holes center distance:59mm*33MMFunction:
1.Timing pull in
2.Timing disconnected
3.Timing pull in and disconnected.
4.Timing off then pull in
5.Infinite loop timing mode 1
6.Infinite loop timing mode 2
7.Finite loop timing mode 1
8.Finite loop timing mode 2
9.Self-lock relay mode
10.Trigger relay mode
11.Trigger timing pull in
12.Trigger timing disconnected
13.Trigger timing pull in and disconnected.
14.Trigger timing disconnected and pull in
15.Infinite loop timing mode 1
16.Infinite loop timing mode 2
17.Finite loop timing mode 1
18.Finite loop timing mode 2
Module Interface:
Module control terminal: 3-wire port, all interfaces are terminal,very easy to use.
DC +:DC positive power(with 5V, 12V and 24V modules to choose from)
DC-:DC negative power.
CH1:input detected port, high level effective.
Relay outputs: 3-wire port, all interfaces are terminals
NO:relay normally open port, relay pull in before as the vacant,after pull in with the COM1 short connection.
COM:relay common port.
NC:relay normally closed port,relay with COM1 short connection before pull in,vacant after pull in.
Load capacity: normally open port maximum load capacity: DC 0-30V / 10A, AC 0-250V / 10A.
normally closed port maximum load capacity: DC 0-28V / 10A, AC 0-125V / 10A
Package included:
1 x FRM01 Multifunction Self-lock Relay Cycle Timer Module PLC Delay
8. KNACRO 5V-30V 1 Channel Wilde Voltage 0-24s Adjustable Delay Internal/External Trigger Relay Board with Timer Delay Conduction Delay Circuit Switch
Feature
Can adjust 0-24 seconds delay time with potentiometer, which is convenient to complete.Two Trigger Mode: Provide an external signal by TRIG, or light touch trigger button.
5-30V wide work voltage, with terminal and micro USB two power supply modes.
With over current protection, pull-up and filter circuit designed mode signal terminal block, strong ability of anti-jamming, suitable for industrial control.
With relay pull indicator light, can directly reflect the current work status.
Description
Size: 5.4*1.9*1.8cmWork Voltage: Wide voltage 5-30V
Output Load: AC 0-220V 10A, DC 0-30V 10A Input Mode: Micro USB interface and solder terminal, two power supply modes.
Signal terminal block has a pull-up and filter circuit designed, strong ability of anti-jamming, suitable for common circuit control or industrial control, can be applied to security alarm delay, building electric light on/off, on-board equipment delay conduction to prevent the excessive current burning out the on-board equipment when the car start, and the occasions that need to be started orderly to prevent the over current burning out the equipment when they start at one time.
Operating Mode:
After powering up the module, the output status: normally open (NO) and the common interface (COM) disconnected, normally closed (NC) and the common terminal (COM) connected.
Providing a low pulse signal to external trigger, or light touch trigger, at that moment, relay pull and indicator lights up, the output state is:
normally open (NO) and Common interface (COM) connected, normally closed (NC) and the common interface(COM) is disconnected. After 0-24 seconds (this time can be adjusted according to your needs) relay disconnecting, back to the state before triggering.
Package Include:
1pcs 1 Channel Adjustable Delay Internal/External Trigger Relay
If you have any question , please feel free to contact us.
Feedback:
We greatly appreciate your POSITIVE feedback. Please do NOT leave negative feedback without asking for help. Our aim is to provide Top Level Customer Service, so we will try our best to solve any problem.Thank you very much!
Please note:
1> KNACRO is a registered trademark and the only authorized seller of KNACRO branded products.
2> KNACRO provide you various kinds of great products at the lowest possible prices, welcome to our store and get what you want !!!
9. DZS Elec 5V-30V 1 Channel Wilde Voltage 0-24s Adjustable Delay Internal/External Trigger Relay Board with Timer Delay Conduction Delay Circuit Switch with USB to Micro USB Power Line
Feature
Can adjust 0-24 seconds delay time with potentiometer, which is convenient to complete.Two Trigger Mode: Provide an external signal by TRIG, or light touch trigger button.
5-30V wide work voltage, with terminal and micro USB two power supply modes.
With over current protection, pull-up and filter circuit designed mode signal terminal block, strong ability of anti-jamming, suitable for industrial control.
With relay pull indicator light, can directly reflect the current work status.
Description
Feature:Size: 5.4*1.9*1.8cm
Work Voltage: Wide voltage 5-30V
Output Load: AC 0-220V 10A, DC 0-30V 10A
Input Mode: Micro USB interface and solder terminal, two power supply modes.
Signal terminal block has a pull-up and filter circuit designed, strong ability of anti-jamming, suitable for common circuit control or industrial control, can be applied to security alarm delay, building electric light on/off, on-board equipment delay conduction to prevent the excessive current burning out the on-board equipment when the car start, and the occasions that need to be started orderly to prevent the over current burning out the equipment when they start at one time.
Operating Mode:
After powering up the module, the output status: normally open (NO) and the common interface (COM) disconnected, normally closed (NC) and the common terminal (COM) connected.
Providing a low pulse signal to external trigger, or light touch trigger, at that moment, relay pull and indicator lights up, the output state is: normally open (NO) and Common interface (COM) connected, normally closed (NC) and the common interface(COM) is disconnected. After 0-24 seconds (this time can be adjusted according to your needs) relay disconnecting, back to the state before triggering.
Package Include:
1pcs 1 Channel Adjustable Delay Internal/External Trigger Relay
1pcs USB to Micro USB Power Line
10. 5V DC Delay Relay Delay with Timer Turn on / Delay Turn off Switch Module (5V)
Feature
5V delay turn on or delay off moduleWith 8 time ranges selected shortest 0.1s most up to 1 hour
Can be accessed by a large current load (250V ac 10A or 30V dc 10A)
Protection against power reversal protection diode, better protection module
With delay adjustment potentiometer clockwise adjustment time longer
Description
Function:
Plug On S6 ,delay turn off
Plug on s7, delay turn on
Specification:
Input Voltage: 5V, 12V
Quiescent Dissipation: 5.5mA
Maximum Power Consumption: 42mA
Relay Load Capacity:
250V 10A AC (2500W ideal power AC)
30V 10A DC (300W ideal power DC)
