If you looking for 0.56 ohm resistor then you are right place. We are searching for the best 0.56 ohm resistor on the market and analyze these products to provide you the best choice.
Reviews
1. uxcell Aluminum Case Resistor 10W 0.56 Ohm Wirewound for LED Converter with Rod Post 10W0.5RJ
Feature
10 Wattage and 0.5 Ohm, 5% tolerance. Wire Wound Resistor owns high stability and accuracy. Moreover, it was used for various application because of the wide resistance range.Aluminum Housed. An insulated cover on the wounded wires would block out the heat, which promises the high performance of a resistor. Hence, the cooling job was achieved by aluminum case.
This 10W resistor formed with qualified copper, nickel, and aluminum. With the compact structure and heat dissipation design, a capability of overload has been built.
Board length 3/4 inches(19mm) and two rods with 1.8mm hole for a soldering connection. Dia. 2.5mm antisymmetric anchoring hole for holding, which will fit #2 Screws(or M2.3 nuts)
Reliable. Problems like the flush LED would have a perfect solution, or you can use it in any AC DC circuits, converter, inverter, motor speed control, drivers, etc.
Description
Main Body Length: 1.9 cm/ 0.75 inchesPower: 10 Wattage
Rated Resistance: 0.5 R
Tolerances: 5%(J)
Connection Type: Rod terminals withhole
Rod Length: 7.7mm/0.3 inches
Screw Hole: 2.5mm(Fit #2 or M2.3 nuts)
Distancebetween screw hole: 14mm
Weight: 6g/0.15 Oz
Materials: Nickel alloys Wire Wound Resistor with Aluminum Case
Color: Gold
Package Content:
1 x 10W0.5R Aluminum Housed Resistor
2. uxcell 10W 5% 0.56 Ohm Resistance Value Screw Tabs Aluminum Case Resistor
Feature
Resistance Value: 0.56 OhmPower Rating: 10W; Resistance Tolerance: 5% (J)
Mounted Hole Diameter: 0.2cm/ 0.078"
Body Size: 1.9 x 1cm/ 0.74" x 0.39" (L*D)
Total Size: 3.2 x 2.1 x 1cm/ 1.2" x 0.82" x 0.39" (L*W*H)
Description
Casing Material: Aluminum;Color: Gold Tone;
Weight: 5g;
Package Content: 1 x Aluminum Wire Wound Resistor;
This resistor designed with gold tone aluminum case, 10 watt power and 0.56 Ohm resistance value;
The aluminum case has the screw tabs on it so you can tighten them against a chassis or heat sink for greater heat dissipation;
Widely used in power supply, transducer, elevator, arena audio and high requirement equipment industry.
3. NTE Electronics HWD56 Metal Film Flameproof Resistor, 1/2W, 5% Tolerance, Axial Lead, 0.56 Ohm (Pack of 2)
Feature
Telecommunications equipmentIndustrial (MRO) equipment
Power supplies
Computers
As replacement resistors in all types of applications where Safety is a concern
Description
The NTN quality line of flame retardant resistors is designed for replacement and original equipment use.4. 2 Watt Metal Oxide Power Resistor, 0.56 Ohm, Pkg. of 5
Feature
Fresh stock, non-surplus, bulk packaging5% Tolerance, 350V max rating
Small and compact with easy to read, standard EIA color code
Operating Temperatures: -55?C to +235?C
Flame resistant coating makes these resistors great for power supplies
Description
Metal oxide resistors are ideal for use in a wide range of high temperature, high voltage environments because of their stable performance and flame retardant coating. Features a flame resistant coating which is a great choice for high power circuits and power supplies. 5% tolerance. Operating Temperature: -55C - +235C, Working Voltage: 350V, Body Length: 16mm, Body Diameter: 5.5mm, Lead Length: 28mm, Lead Diameter: .7mm. Package of five.5. NTE Electronics 5WD56 Through Hole Resistor, Wire Wound, Axial Leaded, 5% Tolerance, 0.56 Ohm Resistance, 5W, 550V (Pack of 2)
Feature
Wire woundAxial leaded
5% tolerance
550 volts
5 watts
Description
The NTE quality line of flame retardant resistors is designed for replacement and original equipment use. They are ideal for use in entertainment products, telecommunications equipment, industrial (MRO) equipment, power supplies, computers.6. NTE Electronics 2WD56 Resistor, Metal Oxide Film, Flameproof, Axial Leaded, 5% Tolerance, 0.56 Ohm Resistance, 2W, 500V (Pack of 2)
Feature
Axial LeadedMetal oxide film
5 percent Tolerance
Description
The NTN quality line of flame retardant resistors is designed for replacement and original equipment use.7. NEW 50 X Resistors 0.56 Ohms 1W Cement 5% Tolerance
Feature
1W 0.56 ohmResistors
Description
NEW 50 X Resistors 0.56 Ohms 1W Cement 5% ToleranceFeatures:
Power:1W
Materials:Carbon Film
Resistance:0.56 ohms
Tolerance;5%
Size:9mm X 3.2mm (Approx)
Parcel include:50pcs 1W resistors
Model:1W Resistor 0.56 Ohms
Buying multiple products at once will be a big discount,please contact US before
8. uxcell Aluminum Case Resistor 10W 0.56 Ohm Wirewound for LED Converter with Rod Post 10W0.56R
Feature
10 Wattage and 0.56 Ohm, 5% tolerance. Wire Wound Resistor owns high stability and accuracy. Moreover, it was used for various application because of the wide resistance range.Aluminum Housed. An insulated cover on the wounded wires would block out the heat, which promises the high performance of a resistor. Hence, the cooling job was achieved by aluminum case.
This 10W resistor formed with qualified copper, nickel, and aluminum. With the compact structure and heat dissipation design, a capability of overload has been built.
Board length 3/4 inches(19mm) and two rods with 1.8mm hole for a soldering connection. Dia. 2.5mm antisymmetric anchoring hole for holding, which will fit #2 Screws(or M2.3 nuts)
Reliable. Problems like the flush LED would have a perfect solution, or you can use it in any AC DC circuits, converter, inverter, motor speed control, drivers, etc.
Description
Main Body Length: 1.9 cm/ 0.75 inchesPower: 10 Wattage
Rated Resistance: 0.56 R
Tolerances: 5%(J)
Connection Type: Rod terminals withhole
Rod Length: 7.7mm/0.3 inches
Screw Hole: 2.5mm(Fit #2 or M2.3 nuts)
Distancebetween screw hole: 14mm
Weight: 6g/0.15 Oz
Materials: Nickel alloys Wire Wound Resistor with Aluminum Case
Color: Gold
Package Content:
1 x 10W0.56R Aluminum Housed Resistor