We spent many hours on research to finding tpa3116 100w mono amplifier, reading product features, product specifications for this guide. For those of you who wish to the best tpa3116 100w mono amplifier, you should not miss this article. tpa3116 100w mono amplifier coming in a variety of types but also different price range. The following is the top 10 tpa3116 100w mono amplifier by our suggestions:
Reviews
1. Yeeco 100W+100W 2 Channel Digital Power Audio Sereo Amplifier Board, DC 12-24V Car Stereo AMP Module for Vehicle Auto Computer Audio System DIY Speakers with Volume Knob Double Chips Heatsink
Feature
Operating voltage range: DC 12-24V(maximum voltage is no more than 24V); LED indicator; logical and delicate circuit layout; ON/OFF volumn adjustment knobUp to 90%, high power efficiency, high power; low consumption; strong resistivity for AM; comprehensive protection: short-circuit/over-heat/over-pressure/direct current and low voltage
With 3.5mm audio input jack and 3-pin audio input port; 3 wiring columns(Left->for left channel output 10-100W; middle->DC 12-24V power supply; right->right channel output 10-100W)
Dual output channel, the maximum output power can reach 100W+100W; this digital audio amplifier board applies to laptop power supply; battery and vehicle battery(DC 12-24V, power supply which more than 100W is recommended)
Dimention: 105mm(Length)x 65mm(Width)x 23mm(Height); perfect size of the amplifier board which will not take you too much room and it is easy to install
Description
Product Information
Power supply: DC 12-24V
Output power: 100W x 2
Input impedance: 51K x 2
Power efficiency: >90%
Output Speaker impedance: 4-8 ohm
Frequency: 14-100KHz
SNR(signal noisy ratio):100db
Output channel: Left channel & Right channel
Size: 105mm*65mm*23mm(Length*Width*Height)
Advantage of the Digital Amplifying:
1. Up to 90% efficiency, high power; low consumption; strong resistivity for AM;
2. Comprehensive protection: short-circuit/over-heat/over-pressure and direct current;
3. High Resolution and low distortion; provide defined trebles and deep bass;
4. No need to considerate about the problem of internal resistance when matching with the speakers;
5. Instead of analog amplifier, digital amplifier can avoid transient intermodulation distortion efficiently
Wiring instructon:
1. Make sure the correct wiring before connecting the amplifier board;
2. Speaker wiring: connects speaker "+" to Lout "-", connects speaker "-" to Rout "-";
3. Connect the audio input wire;
4. Power on the amplifier board after confirming the wiring. Remember to unplug the power if you want to change the wiring or move the board.
Note:
1. Power supply cannot be connected to the output interface of the speaker, otherwise the chip will be damaged;
2. Please mount install this amplifier board on somewhere without metal and other conductive objects to avoid causing short circuit or current sound;
Package include:
1 x TPA3116 100W+100W Digital Power Amplifier Board
2. AOSHIKE 100W TPA3116 Digital Power Amplifier Board TPA3116D2 Mono Channel Audio Amplificador DIY DC12-26V
Feature
DC 12V-26V TPA3116 D2 Amplifier Board,Mono Channel 100W output,100W Amplifiers Amplificador DIY;Low noise, Low distortion, High pressurization;The TPA3116 D2 device provides comprehensive protection against short-circuit, overtemperature, overvoltage, undervoltage and DC faults. In the event of an overload, the device reports a fault condition to the processor, preventing itself from being damaged.
Using TPA3116 D2 chip, wide voltage range: 12V to 26V, efficient D-class operation, both more than 90% power efficiency and low idle loss characteristics. Advanced modulation system configuration, multiple switching frequencies.
The TPA3116 D2 Advanced Oscillator / PLL circuit uses multiple switching frequency options to suppress AM interference, and when used with the Master-Slave mode option, enables multiple devices to be synchronized.
Essence of the collection tradition production process, melts the musical instrument manufacture and the industrial art in a body, the acoustic fidelity is exquisite, is stable.
Description
DC 12V-26V TPA3116 D2 100W Mono Channel Digital Audio Power Amplifier Board Amplificador DIYProduct name: TPA3116D2
Supply voltage: DC12-26 v
Output power: 100w
Signal to noise ratio: 100 db
sound channel : mono
Size: 79 * 54 * 16 mm
Frequently Asked Questions:
1.The amplifier board have current sound and noise when you use it
Answer: Most of the amplifier board is DC power supply. the amplifier board does not produce current sound and noise
The reason of produce current sound and noise:
A.The power filter is not good,The reason of product current sound is abnormal power input and Audio inputs
B.The quality of input signal is poor,the output of the connected device is not normal,the reason of produce noise is abnormal Audio input
C. The quality of the input cable is poor,the wire connection is not well,or wire is broken,the wire connection hung up and so on
D. The input connection has other playback devices,some devices share power to cause the noise
Package included:
1PC TPA3116 D2 Mono 100W Digital Audio Amplifier Board DC12-26V
3. LM YN TPA3116 D2 Mono Channel Digital Amplifier Board NE5532 150W Max Preset Amplifier System Digital Power Amplifier Board DC12 - 26V
Feature
Preset Amplifier System,Mono high power, DC12V / 50W, DC20V / 100W, DC26V / 150W.Using NE5532 high-performance low noise dual operational amplifier (dual op amp) integrated circuits. It has better noise performance, excellent output drive capability and a very high signal bandwidth, power supply voltage range and other characteristics. So it is suitable for high-quality and professional audio equipment, instruments, control circuits and telephone channel amplifier.
Using TPA3116 D2 chip, wide voltage range: 12V to 26V, efficient D-class operation, both more than 90% power efficiency and low idle loss characteristics. Advanced modulation system configuration, multiple switching frequencies.
The TPA3116 D2 Advanced Oscillator / PLL circuit uses multiple switching frequency options to suppress AM interference, and when used with the Master-Slave mode option, enables multiple devices to be synchronized.
The TPA3116 D2 device provides comprehensive protection against short-circuit, overtemperature, overvoltage, undervoltage and DC faults. In the event of an overload, the device reports a fault condition to the processor, preventing itself from being damaged.
Description
Using NE5532 high-performance low noise dual operational amplifier (dual op amp) integrated circuits. It has better noise performance, excellent output drive capability and a very high signal bandwidth, power supply voltage range and other characteristics. So it is suitable for high-quality and professional audio equipment, instruments, control circuits and telephone channel amplifier.Using TPA3116 D2 chip, wide voltage range: 12V to 26V, efficient D-class operation, both more than 90% power efficiency and low idle loss characteristics. Advanced modulation system configuration, multiple switching frequencies.
The TPA3116 D2 Advanced Oscillator / PLL circuit uses multiple switching frequency options to suppress AM interference, and when used with the Master-Slave mode option, enables multiple devices to be synchronized.
The TPA3116 D2 device provides comprehensive protection against short-circuit, overtemperature, overvoltage, undervoltage and DC faults. In the event of an overload, the device reports a fault condition to the processor, preventing itself from being damaged.
Product Name: TPA3116 D2 Digital Power Amplifier Board.
Impedance Range :4 - 6.
Chip Type: TPA3116 D2.
Supply voltage: DC12-26V.
Output power: maximum 150W (DC12V / 50W, DC20V / 100W, DC26V / 150W).
Signal to noise ratio: 100db.
Product size: 77.5 * 73 * 16mm / 3.05 * 2.87 * 0.63in (L * W * H).
Net weight: 67 g / 0.15 lb.
Note:
When you purchase this product, after receipt, do not arbitrarily connect the power and speaker use, refer to the data provided in this product description for reasonable use. Power, voltage, speaker power three unreasonable use may cause the amplifier board damage.
Package Included:
1*NEW TPA3116 Mono channel digital amplifier board
If you for any reason are not happy with any product supplied , please do not hesitate to contact us and we will do our best to solve your problem .
4. WINGONEER DC 12V-24V TPA3116 D2 100W Mono Channel Digital Audio Power Amplifier Board for Car
Feature
DC 12V-26V TPA3116 D2 Amplifier Board,Mono Channel 100W output,100W Amplifiers Amplificador DIY;Low noise, Low distortion, High pressurization;The TPA3116 D2 device provides comprehensive protection against short-circuit, overtemperature, overvoltage, undervoltage and DC faults.
Using TPA3116 D2 chip, wide voltage range: 12V to 26V, efficient D-class operation, both more than 90% power efficiency and low idle loss characteristics.
Description
WINGONEER trademark Reg.NO:4747611WINGONEER DC 12V-24V TPA3116 D2 100W Mono Channel Digital Audio Power Amplifier Board for Car
Description:
Chip Type: TBA3116D2
Power supply: DC 12V-26V
SNR: 100db
Output Power: 100W
Size: 79 x 54 x 16mm
Package include:
1 x WINGONEER TBA3116D2 Audio Amplifier Board
5. WINGONEER TPA3116D2 Mono channel digital amplifier board NE5532 150W DC12-26V AMP Module for Car Home Theater and DIY Audio
Feature
Using TPA3116 D2 chip, wide voltage range: 12V to 26V, efficient D-class operation, both more than 90% power efficiency and low idle loss characteristics.Using NE5532 high-performance low noise dual operational amplifier (dual op amp) integrated circuits.
Mono stereo power amplifier, without noisy and interference current sound.
Large capacity 35V 470MF, the temperature up to 105, which offers stable operationprevent load changes affect the sound quality; the amplifier module adopt european terminals and PCB mini board
Wide used in home theaters and active speaker and diy audio, offer you an auditory feast
Description
WINGONEER trademark Reg.NO:4747611WINGONEER TPA3116D2 Mono channel digital amplifier board NE5532 150W DC12-26V AMP Module for Car Home Theater and DIY Audio
Description:
Chip Type: TPA3116 D2.
Supply voltage: DC12-26V.
Output power: maximum 150W (DC12V / 50W, DC20V / 100W, DC26V / 150W).
Signal to noise ratio: 100db.
Product size: 77.5 x 73 x 16mm / 3.05 x 2.87 x 0.63in (L x W x H).
Net weight: 67 g / 0.15 lb.
Note:
When you purchase this product, after receipt, do not arbitrarily connect the power and speaker use, refer to the data provided in this product description for reasonable use. Power, voltage, speaker power three unreasonable use may cause the amplifier board damage.
Package Includes:
1x WINGONEER TPA3116 Mono channel digital amplifier board
6. SODIAL(R) TPA3116 2x50W Dual Channel + PBTL 100W Mono Digital Amplifier Board Power M
Feature
Amplifier chip: TPA3116Supply voltage: 11 ~ 26VDC DC input reverse polarity protection zone limit
(Recommended 24V DC current switching power supply 3A and above)
Output power: Stereo 50W + 50W, PBTL Mono 100W
Load Impedance: 4 to 8 ohms (speaker impedance)
Description
* SODIAL is a registered trademark. ONLY Authorized seller of SODIAL can sell under SODIAL listings.Our products will enhance your experience to unparalleled inspiration.SODIAL(R) TPA3116 2x50W Dual Channel + PBTL 100W Mono Digital Amplifier Board Power M
Audio input: 2.54mm 3 hub
Board size: 75mm*50mm*25mm
Model: SW-HF23
Material: plastic
Color:red
Package Includes:
1X Digital Amplifier Board
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
7. DROK TPA3116 Digital Power Amplifier Board 12-24V High Power Amplifier Module 50+50W Power Amplifier Chip with Volume Adjustment Potentiometer Switch Support PBTL 100W
Feature
Adopt Tpa3116 high-performance amplifier chip as the core, DC single power supply, wide operating Voltage range(9-25v, maximum Voltage is No more than 25V)Maximum output power: 50W (left channel) + 50W (Right channel), dual- channel output, efficiency up to 90 percent
Support pbtl 100W mono output and reserve mute interface (mute), when needed, can connect to the pre-mute interface devices
Power anti-shock protection design, No pop sonic Boom when turn on/off
Increase the heat sink to meet with high-voltage power supply, cooling at high power output state needs
Description
Product Parameters:Dimension: 85.55526 mm (Not included the projection of potentiometer (15mm))
Operating voltage range: DC 9-25V (Current above 3A, if you would like a higher power, 19-24V/above 4A is more suitable)
Audio input sensitivity: Dual-channel 700mv; Parallel mono 850mv
Speaker impedance: Dual-channel speaker: 3.5-8 ; Parallel bridge mono speaker: 2-4
Maximum output power: 50W (left channel) + 50W (right channel); Parallel bridge mono 100W
Reverse connection protection: Yes. (Positive and negative reversal is not energized.)
Audio input connector: Standard 3.5MM audio line input jack, or from 3P socket input audio.
Reserve mute interface (MUTE), when needed, can connect to the pre-mute interface devices.
Method of Wiring:
1. Check the indicate instruction carefully before wiring.
2. Connect the speaker wire: speaker + connects to Lout -, speaker - connects to Rout -.
3. Connect the audio input wire.
4. Plug in the power after confirming if the wiring is correct. To change the wiring or move the board, you must unplug the power firstly.
Use Notes:
1. Power supply cannot connect to the output interface of the speaker, or the chip will be damaged.
2. The board cannot be placed on the metal surface, electrically conductive objects or wet objects which will cause short circuit or induced current sound.
3. Output power: Tip: To the audio input in sufficient supply voltage / current enough, will have enough output power. Higher relative power supply voltage will be bigger, different speakers have different impedance output power. Under voltage and current enough, the number of speakers in Europe, the smaller the relative sound power, please pay attention!
Package Includes:
1 TPA3116 Amplifier Board
8. Subwoofer Amplifier Receiver 100Watt Mini Hi-Fi Digital Class D Integrated Stereo Audio Amp for Sub Bass + Power Supply
Feature
Come with 19V power adapter that can be carefully matched with this home mono integrated amp physically as well as electricallyAdopt Texas Instruments TPA3116 chip, NE5532 op-amp. No pop, no audible noise, dead silent when nothing is playing through it
Built-in low pass filter,100W X 1(4 ohms, 20 Hz - 120Hz, 0.04% THD, 18db/octacce) for subwoofer, Small simple compact design but practical and powerful
Advanced circuitry design, built-in speakers protection circuit, solid aluminum chassis for long time use
Manufacturer-Direct, free lifetime technical support, and 18-month manufacturer's warranty. Feel free to contact us at [email protected], we will reply to you within 8 hours;
Description
Quick tips:
1. Please plug the power cord into the amp THENthe wall, plug the audio cables into amp THENswitch on.
Some customers may see some slight sparks flying when they plug the power supply into the amplifier, because they use it in wrong way, you need to connect the amp to the power supply first, then plug the power supply into the 110v AC outlet, don't worry about the sparks, because this is class d amplifier, the capacitors need to charge when the power in, it's normal and safe.
Parameter:
1. Power supply range: 12v-24v;
2. THD: 0.04%;
3.Frequency Range: 20Hz - 120Hz (1 dB);
4.SNR: 98dB;
5. Inputsensitivity: 280mV;
6. Terminatingimpedance: 2Ohm - 8Ohm;
7. Output power: 100W for Subwoofer;
8. Input mode: 3.5mm audio input;
9. Power supply: 19V 4.74A 90W;
10.Supplied Accessories: Amplifier, Power supply, AC power cord, Manual.
9. TOOGOO(R) DC 12V-24V TPA3116 D2 100W Mono Channel Digital Audio Power Amplifier Board car
Feature
Condition: NewType:100W Mono Channel Digital Audio Power Amplifier B
Working voltage:DC 12V-24V
Max power output:mono 100W
Full-speed USB support using Windows standard drivers
Description
* TOOGOO is a registered trademark. ONLY Authorized seller of TOOGOO can sell under TOOGOO listings.Our products will enhance your experience to unparalleled inspiration.TOOGOO(R) DC 12V-24V TPA3116 D2 100W Mono Channel Digital Audio Power Amplifier Board car
Real-time execution
Processors run at maximum speeds
MPLAB IDE compatible (free copy included)
Built-in over-voltage/short circuit monitor
Firmware upgradeable from PC/web download
Totally enclosed
Supports low voltage to 5 volts (1.8v to 5.0v range)
Diagnostic LEDs (power, active, status)
Read/write program and data memory of microcontroller
Erase of all memory types (EEPROM, ID, configuration and program) with verification
Freeze-peripherals at breakpoint
Program up to 512K byte flash with the Programmer-to-Go
Basic Debugger System
CAUTION: Do not change hardware connections while the PICkit3 or target is powered
Colour:blue + black
size:79 * 54 * 16MM
material:plastic + metal
Package Contents:1 x Digital Audio Power Amplifier Board
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
10. SODIAL(R) DC 12V-24V TPA3116 Mono Channel Digital Power Audio Amplifier Board BTL Out 100W
Feature
Small size design, BTL output, the maximum output power 100w, can drive 2 ohm speakers, be balanced (differential) input, external heat sink chip work more stable.Signal input mode can be selected according to the following two needs:
Balanced input signal (differential): Signal + Signal -, GND (ground).
Unbalanced inputs (single-ended): - end and GND (ground) short circuit, the signal input from the + terminal.
3300 / 25V filter capacitor
Description
* SODIAL is a registered trademark. ONLY Authorized seller of SODIAL can sell under SODIAL listings.Our products will enhance your experience to unparalleled inspiration.SODIAL(R) DC 12V-24V TPA3116 Mono Channel Digital Power Audio Amplifier Board BTL Out 100W
Board size: 75mm * 50mm/2.95*1.97 inch
Board overall height: 25mm/0.98 inch
Operating Voltage: DC 12v-24v
Maximum output power: 100w (2 ohm speakers connected)
material:plastic
colour:red
Package Contents:1x Amplifier Board
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
