When you want to find dual extruder board, you may need to consider between many choices. Finding the best dual extruder board is not an easy task. In this post, we create a very short list about top 9 the best dual extruder board for you. You can check detail product features, product specifications and also our voting for each product. Let’s start with following top 9 dual extruder board:
Reviews
1. KINGPRINT 3D Controller Board MKS BASE V1.4 RepRap Ramps 1.4 for 3D Printer
Feature
Arduino MEGA compatible Atmega2560 and FT232 processors are compatible with all RAMPS class firmware.4 layers PCB, optimize heat dissipation.
Easy DISPLAY + SD-CARD connector, RepRap Discount SmartController compatible pin header on board.
Up to 5 motor driver with A4982.
Recoverable fuse for short-circuit protection.
Description
Specification:-MKS BASE is a feature rich all-in-one electronics solution for Reprap and other CNC devices.
-It features an onboard ATmega2560. Its five motor outputs are powered by A4982 stepper drivers.
-The board can use the same firmware as Ramps1.4. MKS Base is designed to be flexible in the user's power source availability, allowing any power supply from 12V-24V.
-6x end stop connectors with power supply Xmin/Xmax/Ymin/Ymax/Zmin/Zmax.
-MKS-BASE is suitable for 3D printer manufacturers on batch production, and being used as main control board. Relative to the Ramps1.4, it adds E1 heating output.
-MKS-BASE is suitable for dual-Extruder machine.
Package Included:
1* MKS-Base V1.4 Controller Board
1* USB Cable
2. Geeetech 3D Printer Control Board GT2560 Support Dual Extruder Power Than ATmega2560 Ultimaker, Ramps
Feature
1With built-in features of Arduino Mega2560 + Ultimaker and Arduino Mega2560 + Ramps 1.4 Kit. The GT2560 can be run with software and hardware and also offers a compact size, convenient port, and more stability.2Paired with the high-performance USB Serial Converter FT232RQ, ATmega2560 can be used as the main control chip.
3The main circuit takes over the SMD fuse and the diode of the power port can provide reverse protection to the whole circuit. In addition, 5V USB is a USB port protected with 500mA recoverable fuse.
43 55 Amp MOSFET (with LED indicator, the actual output power is limited by the PCB board and connector), all 3 MOSFETs are equipped with heatsinks to ensure adequate heat dissipation and stable running performance.
5Supports 5 A4988 stepper drivers (3 for X / Y / Z axis, and 2 for extruder); The division of the stepper motor can be set up by dial switch, which eliminates shorting bridges and makes operation easier.
Description
Features: 1.Integrated with the mighty function of the Arduino Mega2560+Ultimaker and the Mega2560+ramps 1.4 kit , GT2560 can not only take full place them on respect of both software and hardware, but also features compact size, more convenient connection, and more stable. 2. Adopt ATmega2560 as the main control chip, coupled with the high-performance USB serial converter FT232RQ. 3. The power pack: operating voltage is 12V-24V; double power supply design feeds for heatbed and logical part separately. The current is 12A for heatbed and 5A for other parts. The cooling fan can support 12V 4. The main circuit adopts SMD fuse tube, the diode added to the power port can provide reverse protection to the whole circuit, in addition, the 5V USB is USB port protected with 500mA Recoverable fuse. 5 3 12v fan output and one PWM output for LED or other lighting equipment. 6. 3 55Amp MOSFET (with LED indicator, the actual output is restricted by the PCB board and the connector), all 3 MOSFET are equipped with heat sink to ensure sufficient heat dissipation and stable operation. 7. Support 5 A4988 stepper drivers (3 for X/Y/Z axis, and 2 for extruders); the subdivision of stepper motor can be setup by dial switch, eliminating jumper caps, easier to operate. 8. 3 temperature sensor input (100k thermistor is recommended) 9. Extended LCD and SD card interface support both LCD2004 and LCD 12864, with which you can print without your PC. 10. The firmware is the prevalent Marlin, which is known for its stability, usability, and high-performance. The specifications of Pin connectors: Motor: XH (2.54mm-4pin) Fan: PH (2.00mm-3pin) Endstop and thermistor: XH (2.54mm-2pin) Package List:1 X GT2560 3D printer controller board3. KINGPRINT 3D Printer MKS Gen V1.4 Controller Board Mega 2560 R3 Motherboard RepRap Ramps1.4 Compatible with USB
Feature
Mega 2560 and ramps1.4 set on a board, to solve complicated Ramps1.4 combination of interfaces, the problem of failure prone.Replace the motor drive, drive and support 4988 8825 drive.
The circuit board with high-quality 4-layer, heat and made a special optimization; ramps are 2 shelves.
Using high-quality MOSFET, and better heat dissipation.
Using a dedicated power chip, support 12V-24V power input, the voltage converter chip to solve the heat problem Ramps.
Description
-Can accept 24V input power under the same system can be hot-bed current is reduced to 1/4, an effective solution to the hot bed MOS pipe heat problems.-Tthe firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4.
- Can be connected to the control panel and 12864LCD Ramps1.4,2004LCD control panel.(Can't be sure to match all of stype of 12864LCD and 2004LCD )
- Reserved for motor pulse and direction output ports for easy plug-in high-current To add a large current (eg 2A, 5A) motor drive circuit.
-Reserved Ramps1.4 on Servos, AUX-1, AUX-2 interface that provides three 5V output, three 12V outputs.
Specification
Type: MKS Gen V1.4 control board Mega 2560
Name: MKS Gen V1.4 control board
Weight: 118g
Application: 3D Printer Part
Weight: 118g
Package Included:
1* MKS Gen V1.4 Control Board
NOTE:
If you find any problem, please contact us at first, and our technical staff will help you to solve the problem at once. Thanks!
4. Rumba+ Motherboard Upgrade Rumba Control Board for 3D Printer Triple Extruder Multi Color 3 in 1 Out Diamond Hotend
Description
compact size: 140mm x 75mmfully integrated all in one solution:
Arduino 2560-R3 compatible (works with Sprinter, Repetier-Firmware, Marlin out of the box)
ATmega16U2 (with enhanced firmware) for high speed USB serial connection (up to 2MBit)
UNIVERSAL POWER:
can be used with 12V-35V for motors / heated bed
integrated high precision power regulators (DC/DC) for:
12V (FAN/Light/...) and
5V (ATmega2560/Logic)
power input selector for ATmega/logic (stand alone or power from USB)
easy DISPLAY + SD-CARD connector:
RepRapDiscount SmartController compatible pin header on board
up to 6 motor driver with easy micro stepping setup (micro switches) which can be used for:
TRIPLE extruder
DUAL Z driver and DUAL extruder
5x temperature ADC connectors for thermistors:
e.g. 3x extruder thermistor + 1x heated bed thermistor + 1x chamber thermistor
5x PWM capable power mosfet outputs (3 with voltage selector for MainPower/12V):
e.g. 3x (MainPower) extruder heater cartridge/power resistor + 1x (12V) fan + 1x (12V) light
1x PWM capable power mosfet with extended cooling area for heated bed
6x end stop connectors with power supply
Xmin/Xmax/Ymin/Ymax/Zmin/Zmax
can be used for mechanical, opto, hall, ... end stops
screw terminals *and* pin header for easy motor connection:
can be used with existing 4 pin Molex plug on motor cable, easy to attach cables without plug
USB connector and USB pin header (useful when mounting in a small box).
Power and ALL unused pins available on EXP-3 feature connector:
+5V And +12V; 2x ADC; 2x PWM I/O; 4x I/O; I2C
5. KINGPRINT KFB2.0 Controller Board for Reprap Mendel Prusa I3 Kossel 3D Printer
Feature
The power buck chip using XL1509 chip, high efficiency, stability. Short circuit protection, 150KHz fixed switching frequency 2A current input 12 ~ 40V input voltage.USB serial chip using CH340T chip, the largest 2Mbps, communication Stable, to solve the streamlined version of the Windows driver cannot be installed Problem, support for a full range of Windows, mac, liunx operating system.
The processor uses tamega2560 chip, 54 output to meet the various Output Interface.
Tantalum capacitor filter acquisition temperature, anti-interference, more accurate.
Heatbed MOS tube with F8736 chip, the maximum 18A current.
Description
NOTE:1. When energized, do not connect to the motherboard or replace the different module interfaces.
2. Pay attention to the Positive and negative of the wire.
3. Please check to determine whether the connection interface is correct, so as not to damage the motherboard before open telegram.
4. When in emergency occurs, please press the RESET button on the motherboard or disconnect.
Package Included:
1pcs * Controller Board
1pcs * USB
6. KINGPRINT NEW 3D Printer Control Board MKS BASE Development Board V1.5 Board RepRap Ramps1.4 Compatible
Feature
Arduino MEGA compatible Atmega2560 and FT232 processors are compatible with all RAMPS class firmware.4 layers PCB, optimize heat dissipation.
Easy DISPLAY + SD-CARD connector, RepRap Discount SmartController compatible pin header on board.
Up to 5 motor driver with A4982.
Recoverable fuse for short-circuit protection.
Description
Specification:-MKS BASE is a feature rich all-in-one electronics solution for Reprap and other CNC devices.
-It features an onboard ATmega2560. Its five motor outputs are powered by A4982 stepper drivers.
-The board can use the same firmware as Ramps1.4. MKS Base is designed to be flexible in the user's power source availability, allowing any power supply from 12V-24V.
-6x end stop connectors with power supply Xmin/Xmax/Ymin/Ymax/Zmin/Zmax.
-MKS-BASE is suitable for 3D printer manufacturers on batch production, and being used as main control board. Relative to the Ramps1.4, it adds E1 heating output.
-MKS-BASE is suitable for dual-Extruder machine.
Package Included:
1* MKS-Base Controller Board
1* USB Cable
7. Witbot MKS-Gen V1.4 Controller Board Integrated Ramps 1.4 and Mega 2560 Mainboard with Cable Line for RepRap 3D Printer
Feature
Mega 2560 and ramps1.4 set on a board, to solve complicated Ramps1.4 combination of interfaces, the problem of error-proneThe circuit board with high-quality 4-layer, heat and a special optimization; ramps are 2 shelves
With a dedicated power chip, support 12 V-24 V power consumption, the voltage converter chip to solve the overheating problem ramps
Can 24 V input power under the same system can hot-bed stream reduces 1/4, an effective solution for the hot bed MOS tube heat problems
The firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4
Description
Specifications:
Replace the motor drive, stick and support 4988 8825 stick
With high-quality MOSFET, and better heat dissipation.
Connected, control panel and 12864LCD Ramps1.4, 2004LCD control panel. (Can not be sure to bring all the stype 12864LCD and 2004LCD).
Reserved for motor pulse and direction output terminals add a large current (for example, 2A, 5A) engine for easy plug-in.
Reserved Ramps1.4 on servos, AUX 1, AUX-2 interface that has three 5 V output, three 12V outputs.
Please do not connect positive and negative electrode reversely.
Please do not plug/unplug or adjust the current of the stepper motor drive while it is working.
Please note, this board has two colors, you received board color is random
Package Included:
1*MKS-Gen V1.4 Controller
1*Cable Line
8. BIQU MKS-Base V1.4 Plate Controller Board for 3D Printer Ramps 1.4
Feature
Using 4982 as a motor drive, and a 4988 performance fairly, but with SOP package, heat dissipation will be betterThe circuit board with high-quality 4-layer, and made a special heat treatment optimization; ramps are 2 shelves
Using a dedicated power supply chip, support 12V-24V power input, the voltage converter chip Ramps solve the heating problem
Could accept 24V input, the same system power can heat the bed current is reduced to 1/4, an effective solution to the hot bed MOS pipe heat problems
The firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4
Description
Specifications:
A collection of all the functions on a single board to solve the complicated interfaces Ramps1.4 combination, problem-prone fault
Using high-quality MOSFET tube heat better
Control panel and can be connected directly Ramps1.4,2004LCD 12864LCD control panel
Net Weight:80g
Dimension:110*90mm
Note:
Before powering up again confirm whether the positive and negative reversed, if the user is due to reverse power and burn, and we do not guarantee such problems
Do not plug in case of power motor drive easily lead to burn; do not adjust the current in the motor is running. The correct approach is to first disconnect the power, unplug the motor, and then re-power, adjust potentiometer, measure the voltage on the potentiometer until the measured voltage is the same as expected
MKS-BASE is to create customer base for R & D personnel Ramps1.4, Megatronics V2.0 and other open source motherboard problems especially developed to optimize the launch of a product, particularly suitable for mass production 3D printer manufacturers use as the main control board
Give full consideration to the stability, heat dissipation, ease of use issues through continuous printing reliability testing
If special needs can contact the owner with details
Supporting line can refer to: 2PIN, 3PIN, 4PIN
Could be directly connected 2004LCD or 12864LCD (remove the L-shaped adapter plate), due to the open-source design 12864LCD 2004LCD and only standardized EXP1 and EXP2 the PIN port on the horns insertion direction and there is no specific standard, so some non Makerbase production and 2004LCD 12864LCD may be inconsistent data line card port direction, in turn, need to plug to use
Package Included:
1* MKS-Base V1.4 3D Printer Controller Board
1* USB Cable
Note: The socket color is ramdon, please double confirm you do not mind before placing order.
9. KINGPRINT MKS-Gen V1.4 Controller Board+5PCS DRV8825 stepper motor Mega 2560 motherboard RepRap Ramps1.4 compatible +USB Cable for 3D Printer
Feature
The firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4.Reserved for motor pulse and direction output ports for easy plug-in high-current To add a large current (eg 2A, 5A) motor drive circuit.
Reserved Ramps1.4 on Servos, AUX-1, AUX-2 interface that provides three 5V output, three 12V outputs.
The circuit board with high-quality 4-layer, heat and made a special optimization; ramps are 2 shelves.
Can accept 24V input power under the same system can be hot-bed current is reduced to 1/4, an effective solution to the hot bed MOS pipe heat problems.
Description
Specification: Can be connected to the control panel and 12864LCD Ramps1.4,2004LCD control panel.(Can't be sure to match all of stype of 12864LCD and 2004LCD )MEGA2560 and RAMPS 1.4 set on a board, to solve complicated RAMPS1.4 combination of interfaces, the problem of failure prone.
Support up to 5 motor driver (A4988 or DRV8825).
Using a dedicated power chip, support 12V-24V power input, the voltage converter chip to solve the heat problem Ramps.
Package Included:
5 * DRV8825S Stepper Motor Driver
1 * MKS-Gen V1.4 Controller Board
1 * USB Cable
5 * Mini Heat Sink
