If you looking for co2 laser machine 60w then you are right place. We are searching for the best co2 laser machine 60w on the market and analyze these products to provide you the best choice.
Reviews
1. TEN-HIGH AC110V glass laser tube 60W CO2 1000mm length, 50mm Dia for 400x300mm 60W laser engraving and cutting machine
Feature
Isolation Withstand voltage,Response time<1msProtection: with well-grounded enclosure, output circuit of power supply can be open for short time
TTL voltage level control: effective voltage level can be high or low through setting
Protection switch: for detection of cooling water, to protect laser device
Laser power adjustment:adjusting the output current of power supply through resistor/PWM control
Description
Notice:1.Here is the laser engraver with this laser tube for your reference:
https://www.amazon.com/dp/B01D2PPA2C
2.To purchase a laser tube,please confirm your machine's installation space,like the diameter and length,all should be a little bigger than laser tube's size
Introduction
Model:CO2-TUBE-60W-1000MM
Output Power:60W
Dimensions:Length 1000mm
Protection: with well-grounded enclosure, output circuit of power supply can be open for short time (but arc between positive pole and enclosure should be avoided).
Response time (from time of input being available to the output current being up to nominal value)<1ms
TTL voltage level control: effective voltage level can be high or low through setting.
Protection switch: for detection of cooling water, to protect laser device; or activate with enclosure is opened.
Laser power adjustment: (1) by adjusting the output current of power supply through resistor; (2) through PWM control (magnitude being TTL voltage level).
Environmental requirements: temperature (-10 to 40 centidegree), relative humidity<85%.
2. Cloudray 60W Co2 Laser Power Supply 110V for CO2 Laser Tubes MYJG-60W Buy More Discounts
Feature
Good compatibility: it can be applicable to 60W Laser Tube manufactured by various factories.Quick response speed and effect,high performance,large cutting power,it also can prolong laser tube service life.
Easy control: the start and stop of laser can be easily controlled by TTL level.
The power supply has output open circuit protection, TTL signal indication, water through signal indication and laser output indication. And the Buttonto test output laser manually.
Application: Sculpture and cut acrylic,fabric,double color sheet and rubber etc.
Description
Features:
1. Zero-current half-bridge soft-switching circuit. Highefficiency and fast response. Match various
manufacturers of laser tubes.
2. Simple Port Control,TTL level signalscan control the laser start/stop.
3. Protection switch is to check the outsidewater, ventilation, etc.
4. Laser Power Adjustment: input 0V to 5V analogsignal, can also input PWM signal.
5. Open Circuit Protection Function: avoid the damageto laser power supply due to laser tube burst.
6. Factory Aging Test: 1. Each power supply will go through60 and 12 hours aging test under full load. 2. 500 times 7 secondsStart / Stop test.
Packing List:
Co2 Laser Power Supply x1pcs
Includes Flyback Transformer
3. CNCShop Laser Engraving Machine Laser Cutting Machine Co2 Laser Engraver 40W Carving Tools Artwork Milling Woodworking (40W)
Feature
Engraving Area: 300*200mm; Machine Dimensions: 800*500*250mmLaser power: 60W; Engraving Speed:0-13.8 in./sCutting Speed:0-1.38 in./s; Operating Temperature:32-113F
This laser engraving machine has high precision Stepping motor making engraving more precise.
This laser engraving machine with reinforced and thickened machine body make transportation absolutely to be safer and longer life time.
This 40W laser engraver machine is suitable for various materials, such as bamboo piece, double-color planks, boulder, horns, leather, crystal, wood, organic plastic, abrics, paper ,film, canvas , Acrylic and Plastics..
Description
Co2 40W Laser Engraving Machine with USB Port
Description:
This 40w laser engraving machine is suitable to seal engraving, advertisement, art gift, garment, leather, toy, building upholster, computerized embroidery, packing and printing, paper product, garments sampling, large width tailoring, shoemaking, furniture, industry, craftwork, nameplates decorations, woodcut and other industries.
Technical Parameters:
Interface to Computer: USB Port
Laser Type:CO2 Gas
Current:0~22mA
Engraving Area: 300*200mm
Maximum Item Size to Engrave: 260*220 *70mm
Laser Tube:1000-1300 Hours
Laser Power:40W
Engraving Speed:0-13.8 in./s (0-350mm/s)
Cutting Speed:0-1.38 in./s (0-35mm/s)
Minimum Shaping Character:0.04 X0.04in (1mm X 1mm)
Resolution Ratio:0.001 in (0.026mm) / (1000dpi)
Power Supply:110V 60Hz
Resetting Positioning:0.0004 in (0.01mm)
Motor Type:Stepper Motor
Software Supported: CorelDraw software
Power Consumption:250W
Operating Temperature:32-113F
Water Cooling:Water Pump include
Recommended Spare Parts/Consumables:Laser Tube, Focal lens,Reflection lens
Package List:
1 x CO2 LASER Engraver; 1 x Water Pump ; 1 x Smoke Pipe ; 1 x Smoke Fan ; 1 x Power Wire ; 1 x USB Cable ; 1 x USB Key ; 1 x Accessory Bag ; 1 x Instruction Video; 1 x English User Manual
4. TEN-HIGH Upgraded Version CO2 400x600mm 60W 120V Laser Engraving Cutting Machine with USB Port
Feature
INDUSTRIAL-GRADE LASER HEAD: Precision metal mold laser head, adjustable laser energy, wear-resistance, heat resistance, red light positioning system once positioning, positioning can be seen, accurate and efficient.LEADING BRAND LASER TUBE: The leading brand laser tube has high quality, reliable performance and durability.
TEMPERATURE CONTROL DISPLAY: The cooling water temperature is always displayedsafe and convenient.
Electric lifting system & CNC DISPLAY PANEL: Build-in Lift-platform. Simple buttons, digital display, and visual operation.
HIGH-POWER AXIAL FAN: Excellent suction effect, high speed, low noise, anti-corrosion and anti-oxidation treatment.
Description
Item specifications
Model name:TH-CO2-460-60W
Laser Type: CO2 Gas
Wavelength:10.64um
Electric lift platform:0-300mm Laser Power: 60W
Engraving Speed: 3000mm/min
Cutting Speed: 1800mm/min
Power Supply: AC 110V 60Hz / AC 220V 50-60Hz . Please tell us what voltage you want after you buy this item.
Motor Type: Stepper Motor
Software Supported: We offer you two softwares---Coreldraw and
LaserCRW. Coreldraw is used to carve and cut and LaserCRW is used to
carve the seal. We no longer use Moshi software.
Operating Temperature: 5-45C
Working Humidity:5%-95%
Water Cooling: Water Pump include (AC 220V/AC110V 50HZ
Recommended Spare Parts/Consumables: Laser Tube, Focal lens, Reflection lens
Adjustable laser energy
water temperature control protection
Blowing flame retardant
Red positioning
Communication monitoring
Continue carving after poweroff
Engraving Materials---Matched:
All non-metal meterials, like Acrylic, Plywood, Density board, Solid wood, PVC, Cortical, Leather, Non-woven fabric, felt, Paper products, Double color plate, PET, etc.
For metal:
Only engraving the coat of paint on the metals , if you want to engraving the metals, please contact.
Applicable Industry:
This machine is suitable to seal engraving, advertisement, art gift,
garment, leather, toy, building upholster, computerized embroidery,
packing and printing, paper product, garments sampling, large width
tailoring, , shoemaking, furniture , model industry, craftwork and
other industies.
5. Iglobalbuy Cylinder Rotary Axis Rotary Attachment Laser Rotary Axis for 50w 60w 80w 100w 130w Co2 Laser Engraving Machine
Feature
This 360 rotary axis is applicable to 50/60/80/100W C02 laser engraverWith C type steel frame and aluminum axis, this axis is very durable and stable
With fast response stepper motor and aviation plugs, this axis has very high precision
his axis has 3 roller diamond plane axis and two separate spaces for different size stuff
It is widely used in engraving bamboo, wood, paper, plastic, leather, rubber etc
Description
Item Specification:Color:black
Axis length :13.98"(35.5cm)
Axis diameter:1"(2.5cm)
Package Size:18.11'x14.17"x4.09"(46x36x10.4cm)
Product Frame Size:16.34"x15"(41.5x38.3cm)
Weight:9.85lb
Package:
1xCylinder Rotary Attachment
1xStepper motor
6. Superland CNC Router Rotary Axis for 60W CO2 Laser Engraving Cutting Machine Engraver USB Port Great with 80mm Accessory 230mm Track (Rotary AXIS)
Feature
Rated Voltage:2.07v Dc; Phase Resistance (20) 1.38(115%)/PhaseThe Maximum Statictorque780mn.M; Swing( Shaft To See ):A-Ab-B-Clockwise Direction
Maximum No-Load Running Frequency2500pps; Electrical Strength:Ac600v/1ma/1s
Closed-Loop Control, No Longer Lose Any Steps, Up To Its Maximum Torque; Reduced Motor Heating And More Efficient
Smooth Motion And Super-Low Motor Noise; Higher Torque And Higher Speed; No Tuning And Always Stable; Zero-Speed Stability
Description
CNC Router Rotary Axis Rotary Attachment Laser Rotary Axis for Co2 Laser Engraving Machine with 80mm Accessory 230mm Track
80mm 3-Jaw Scroll Chuck
Stainless Anti-Dust Cover
Surface Steel Plate With Anti-Rusty Coating
Ratio: 1:2.5 Synchronous Pulley Induction
Maximum Holding Range With Jaws:2-70mm
Fast Response
Lower Cost
Specifications
Rotor Inertia:220g.
Step Angle:1.80.09
Rated Current:Dc 1a/Phase
Inductance (1khz):30(120%)Mh/Phase
Detent Rorque:320g.Cm Ref.
Maximum No-Loadstart Frequency1500 Pps
Insulation Resistance100m(Dc 500v)
Insulation Grade:B
Quality 0.8kg Ref.
Material Of Pulley:H62
Tooth Form:Mxl
Number Of Teeth Z=20
Pitch Of Teeth P=2.032
Pitch Circle:12.936
Outer Circle:12.4280.003
Package Content
1 X Rotary Axis
7. Ten-HIGH Laser Engraving Cutting Machine 400x700mm 60W CO2 Laser Engraver,Standard Version with USB Port, Include Rotary axis.
Feature
Front-Rear Double Door & ROTARY AXIS: Front-Rear Double Door for object with no-limited length,Less size restrictions to engraving materials, With rotary axis, rolling engraving.INDUSTRIAL-GRADE LASER HEAD: Precision metal mold laser head, adjustable laser energy, wear-resistance, heat resistance, red light positioning system once positioning, positioning can be seen, accurate and efficient
LEADING BRAND LASER TUBE: The leading brand laser tube has high quality, reliable performance and durability
Function: Big energy,laser engraving and cutting function,Electric Build-in Lift-platform
Electric lifting system & CNC DISPLAY PANEL: Build-in Lift-platform. Simple buttons, digital display, and visual operation.
Description
NOTICE:We will provide a safe and reliable packaging, the damages in the transport link will be compensated and replaced by our part.
We just provide Engraving machine driver plug-in (CorelLASER / LaserDRW), Don't provide CorelDRAW software, so make sure that you have installed the right version, otherwise you will not be able to use the the engraving machine.
As the height of the rotary axis is 50mm, the height of the engraved product with the rotary axis cannot exceed 250mm. If you are not sure if the machine meets your needs, please ask online service. And in order to make sure you have bought the right machine, please tell us the type of material you need to engraving or cutting as well as the patterns after you ordering. We will make samples using the machine that you ordered. and send you the pictures or video of the samples, then you can confirm if the machine meet your requierments. This is very important! We don't want our customers to lose money and time when they receive the machine.
Specifications:
Communication Interface: USB port; Laser Type: CO2 Gas
Wavelength: 10.64um; Engraving Area: 400x700mm
Automatic lifting height: 300mm; Laser Power: 60W AC110V / 60Hz
Engraving Speed: 0-500mm/s; Cutting Speed: 0-30mm/s
Cutting/Engraving accuracy: 0.15mm; Carving Depth: 0-2mm (Depend on the material)
Maximum cutting thickness: 10mm (Acrylic) (Depend on the material)
Plugin: CorelLASER / LaserDRW
System: best for WIN7/WIN8/WIN10 32-bit, also suitable for 64-bit
Machine size: 1330 * 740 * 1100mm; Net Weight: 130kg
Typical Consumables replacement parameters:
Laser Tube: 60W L1200mm Diameter 55mm
Focal Lens: Diameter 18mm /focal length 50.8mm
Reflection Mirror: Molybdenum Mirror 20mm
Attention: This machine has equipped with a rotary axis. It can engrave on curved, rounded or spherical surfaces.
8. Mophorn Water Chiller 9L Capacity Industrial Water Chiller CW-3000DG Thermolysis Type Industrial Water Cooling Chiller for 60W 80W Laser Engraving Machine (CW-3000DG 9L)
Feature
Specifcation Model:CW-3000 Industrial Chiller ;Tank capacity: 9L;Amount of Cooling: 50W/Application:CW-3000DG Thermolysis Type Industrial Water Chiller is designed for cooling the one CO2 glass laser tube under 80W of the laser engraving and cutting machine. (Its emitting rate is lower than 60%)
Professional forced air-cooled radiator,high heat dissipating capacity and not easy to be blocked,and equipped with alarm output port, can quickly protect sensitive components
This economic water cooling equipment , a small thermolysis water cooler, can save energy , has long working life and operate simply
This CW-3000 water chiller, comprehensive reference to the international radiator - type cooling system, is suitable for small water cooling device
Description
CW-3000 Industrial Water Cooling Chiller for CO2 Laser Tube Engraver Cutting Cutter
Introduction :
This water chiller is designed for cooling the spindle of the cnc engraving machine,applied to cool a single 80W or below CO2 laser tube (emitting rate lower than 60%),This Water Chiller has been sold largely to Europe, South America, Asia and other markets. Economic cooling equipment, easy to install and operate, compact and easily movable
Technical Datas
Voltage: AC 1P 220V
Frequency: 60Hz
Current: 0.45A
Radiating capacity: 50W/
Tank capacity: 9L
Maximum Pumping Lift: 10M
Maximum Flow: 10L/min
Protection: Flow alarm
Inlet and outlet: External Dia.10mm brass connector
Way of Circulation:Water pump forces circulation
Cooling:Radiator that forces the wind cooling
Feature:
Comprehensive reference to the international radiator - type cooling system
Small thermolysis water cooler
With completed water flow and over high temperature alarm functions
Enclosed water tanks
Professional forced air - cooled radiator
Equipped with alarm output port
Multiple power specifications; CE approval; RoHS approval
Advantages:
CW-3000 laser water chiller is suitable for small water cooling device
Provide stable working conditions for laser devices
Water can be used for a long time
High heat dissipating capacity and not easy to be blocked
Alarm output port can quickly protect sensitive components
Package Content
1 x CW3000 Water Chiller Machine
1 x Power Cable
1 x Connection Hose
1 x Spare Fuse
1 x User Manual
1 x Alarm Signal Output Plug
2 x Sealing Washer
9. Ten-HIGH CO2 60W 110V 300x400mm Laser Engraving Cutting Machine with USB Port.
Feature
INDUSTRIAL-GRADE LASER HEAD: Precision metal mold laser head, adjustable laser energy, wear-resistance, heat resistance, red light positioning system once positioning, positioning can be seen, accurate and efficient.LEADING BRAND LASER TUBE: The leading brand laser tube has high quality, reliable performance and durability.
TEMPERATURE CONTROL DISPLAY: The cooling water temperature is always displayedsafe and convenient.
Electric lifting system & CNC DISPLAY PANEL: Build-in Lift-platform. Simple buttons, digital display, and visual operation.
HIGH-POWER AXIAL FAN: Excellent suction effect, high speed, low noise, anti-corrosion and anti-oxidation treatment.
Description
Dear, After you place the order, please contact us to get manual and software, and operating video, also, as different countries with different Coreldraw version, so make sure that you have install the Coreldraw and working well.Item specifications:
Model name:TH-CO2-430-60W
Communication Interface: USB port
Laser Type: CO2 Gas
Wavelength:10.64um
Engraving Area: 40x30cm
Adjustable Height of Engraving Area:15 CM
Laser Power: 60W
Engraving Speed: 0-30000mm/min
Cutting Speed: 0-3600mm/min
Resolution Ratio: 0.026mm
Power Supply: AC 110V 60Hz / AC 220V 50-60Hz . Please tell us what voltage you want after you buy this item.
Motor Type: Stepper Motor
Software Supported: We offer you two softwares---Coreldraw and
LaserCRW. Coreldraw is used to carve and cut and LaserCRW is used to
carve the seal. We no longer use Moshi software.
Operating Temperature: 5-45C
Working Humidity:5%-95%
Water Cooling: Water Pump include AC120V 50HZ
Recommended Spare Parts/Consumables: Laser Tube, Focal lens, Reflection lens
Engraving Materials---Matched:
All non-metal meterials, like Acrylic, Plywood, Density board, Solid wood, PVC, Cortical, Leather, Non-woven fabric, felt, Paper products, Double color plate, PET, etc.
For metal:
Only engraving the coat of paint on the metals , if you want to engraving the metals, please contact.
Applicable Industry:
This machine is suitable to seal engraving, advertisement, art gift,
garment, leather, toy, building upholster, computerized embroidery,
packing and printing, paper product, garments sampling, large width
tailoring, , shoemaking, furniture , model industry, craftwork and
other industies.
